Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi all, I have recently converted a C9115AXI successfully using the steps below: https://www.cisco.com/c/en/us/support/docs/wireless/embedded-wireless-controller-on-catalyst-access-points/215303-embedded-wireless-controller-conversion.html I did exac...
Hello,Have sort of a general knowledge question: if you have an SSID that has Open security, say a guest network, does that SSID participate in 802.11r even though with open security you cannot toggle on 802.11r?
Resolved! C9120AX-C Not able to join 9800 WLC
C9120AX-C was previously joined to the controller, but for some reason it stopped working. Upon checking it disappeared from the controller. The last join attempt stats below
HIWe have switches connected over a wireless bridge, however VTP information is not sent across correctly.I have seen old community posts with older models, wondering if there is any official Cisco document suggesting that VTP will or will not work a...
Hi,There is C9120 EWC with 17.6.4 IOS-XE.Now I plan to add IW6300 into this EWC. It shows below error informationAP Image Version 17.3.8.21 backup 0.0.0.0, Controller 17.6.4.56 Version does not match.How to upgrade IW6300 version to compatible with E...
I have a problem when I enable PEAP in the Flex profile for the one site, the following error appears:Error in configuring Flex profile - AP local auth is not enabled
Hello everyone, I´m from Argentina, it is not easy to get equipment here, my supplier abroad can provide me the Access Point but not the licenses, is there somewhere where I can purchased directly from a website with a credit card?Thank´s in advance
Cisco AP led blinks cycling: Red - Green - BlueBut it seems I do not have any issues with power:WiFi SSID was searched/scanned with a few phones and laptops, none of them could see SSID.
Hi There,A client is looking to create a new Meraki wireless network with some new devices that would only serve a certain area of the building and keep that traffic isolated (originated on the SSID that would be dedicated to that network). it will h...
3 X 10/100/1000 Base-T (Ethernet) Downlink Interfaces (LAN1, LAN2, LAN3)To perform a link-up check for,The "show ip int brief administratively down" command indicates that the statusIt's there.The "no shutdown" command changes the status of each down...
Resolved! New MR 30.7 stable release candidate firmware:security, reliability, performance, connectivity fixes
Wireless firmware versions MR 30.7 changelogImportant noteWEP deprecation (https://documentation.meraki.com/MR/Encryption_and_Authentication/WEP_Deprecation_on_MRs)Legacy product noticeWhen configured for this version, MR12, MR16, MR18, MR24, MR26, M...
I have self registration guest SSID that set to " Users Must click on the verification Link below " My problem is that even after the guest click on the verification link, it will drop connection after 10 min . and they need to reauthenticate with th...
We are having an issue where the guest portal is not bringing up the redirect page for authentication on Android devices. All other devices are showing the portal without any problem We are using a Cisco WLC 5520 and use ISE version 2.6.0.156 patch 1...
Hi, We have one posture enabled SSID in our wireless network. It is not seamlessly work compared to other SSIDs. The main difference is posture feature has enabled on it. Below are the list of issues. Please share your experiences to overcome from th...
My apologies if this question has already been asked but it's unclear to me in any documentation I've come across.Meraki Wireless is implemented in the environment. The SSID's that are configured for example are HOHT_Guest, HOHT_Internal and HOHT_IoT...
