Hello, i have Cisco 2600 series device and it got a problem. Some one got it reset and erased all files from the boot.Any idea what do i need to do to restore it ?? some one told me i need to get tftp server.And the cisco flashing in red light
Forum Posts
Hi Team, We need to pull the social media usage guest SSID report from Cisco WLC. Please advise: ++ if possible, to get the social media report for users while connected to guest WiFi. ++Which website users are using while connected to guest WiFi. ++...
Resolved! APs fallback to DHCP
Hi,all our APs are with static IPs. Now and then APs fallback to DHCP mode and I can't figure out why. Can I disable the IP fallback feature?Regards,Petri
Hi all, I have 5520 WLC on code 8.5 with 3802, 2802 and 1552 AP models registered to it. Now, I need to add 9120 Aps to my network. Upon upgrade of 5520 WLC to 8.10 code, the existing 1552 Aps will not support the newer version. So, i am planning to ...
How do I assign a static IP address to a AIR-LAP1522AG-A-K9 runing IOS image c1520-k9w8-mx.124-21a.JA? All lwapp and capwap commands are disabled and set commands do not carry through the boot process. I am trying to build a bridge using 2 AIR-LAP15...
I’m working on a packet tracer project where I have to create 3 LANs and connect them and show data and voice connectivity between each. However, only one has IP phones and I can’t figure out how to make the smartphone make a call to show the ability...
Resolved! APs Cannot join the Controller
Hi all,My APs can't join the C9800-CL ver 17.6.5. The controller is run on a HyperV server.1) Certificate is configured, and I see it with: sh wireless management trustpoint. 2) I configured the DHCP scope in the controller 3) Checking the DHCP bindi...
Hello ExpertsWe got a small setup with 6 standalone AP model 1142. DHCP server is Windows 2003, all were working fine but lately we noticed that AP cannot provide IP address to users, this happens to all AP now. on checking we didnt find any issue w...
I have trying to join my new AIR-AP2802I-D-K9 with the same AIR-AP2802I-D-K9 WLC, but its shows the error massage "Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10)"
Resolved! C9136 XOR Sniffer mode crash
Hi,I am using 17.8.1 (9800CL) with two C9136 APs. I am creating this discussion in hopes to find other people with the same problem. My problem is that the sniffer mode works for a while, but then out of the blue it stops working and you have to rese...
I have a Cisco 2602i that will not join a Cisco 5508 WLC.When I watch the AP start up from console I see these messages:*Jun 13 16:55:09.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller*Jun 13 16:54:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection ...
Hi, We had an issue with APs whose certificates have expired. However, we have upgraded the WLC to the fixed version 8.5.182.7, but I still have the same problem. What could be the solution? When I enable 'config ap cert-expiry-ignore {mic|ssc}', the...
Hello, I hope you are well. I have a question about the cisco WLC3500, if I perform a factory reset on the WLC3500 controller, will the permanent licenses that are in it be lost? Thanks in advance for the support.
Hi, I have a WLC 9800 and I want receive alerts of Rogue Malicious (Rogue APs and SSID) by email. Is it possible to configure this on WLC 9800? Another possibility would be to send this alerts from WLC 9800 to Solar Winds Monitoring (NMP). I don't fo...
Hi All,I would like some help on how to proceed in debugging the issue below for example, what type of logs etc. to collect and analyze. Issue: I have 2802i in mobility express mode with 8.10.185.0 version installed. Another 2702i connects to this ME...
