I have a problem with AP 1815i as it continuously disjoin the controller 9800 and restart and then loop in same action as shown in attached logs. These are the port configuration ==============Access switch============== interface gi1/0/21description...
Forum Posts
Will just reload after the output command below ...initializing Hardware ...System integrity status: 90170200 12030106System Bootstrap, Version 16.10(2r), RELEASE SOFTWARECopyright (c) 1994-2018 by cisco Systems, Inc.Current image running: Boot ROM0L...
Hi, I have a CW9166 I-E AP and it is in Factory reset mode. I am trying to login to the console with below crediantials but unable to login.Cisco/Cisco, admin/admin, meraki serial number and no password.What is the correct credentials to login to the...
Hi I am using WLC 9800 ( hardware based) and 9166l LWAP .i have enforced qos policies to ap.I basically tried to priorities Video packets.When i am capturing pacp at controller after connecting the client to WLC, i can see that the traffic is going ...
Resolved! 17.9.4 | CSCwd80290
Hello Everyone,We are currently running a 9800-40 on 17.9.4We took down multiple AIR-CAP2702I-B-K9 and now we are looking to reinstall them. They are doing exactly what is described in the bug CSCwd80290.I noticed in the article below, to fix the bug...
I'm checking for potential wiring issues on a 2800 via CLI. I did a "show int wired 0" and I'm not sure how to interpret the results. Rx err shows 125/0 while Tx is 0/0. Does that mean there have been 125 Rx errors on the interface, or something else...
Hi all I just want to ask you guys about this ErrorsI have Fcs Erros in Received Interface Is it okey guys?I use 10Gig Sfp type LRSoftware 8.5.151
Hello all, I am having issues with wireless controller Catalyst model 9800 L-F and access point model AIR-CAP3702i-A-K9. I have 2 of these access points and only one of them is able to join the WLC. The one giving me issues has a solid green light ...
Resolved! WLC MGMT Interface Access Control
Hello, Cisco Community,With the recent announcement of multiple vulnerabilities in Cisco IOS XE Software Web UI Feature, CVE-2023-20198 and CVE-2023-20273 respectfully. I have taken to closing any holes that afflict our environment. My concern (howev...
Does anybody here have installation examples (pictures) especially from a Cisco 2602/2702/2802 with the external antenna AIR-ANT2566P4W-R in a warehouse enviroment and a installation on the ceiling? Thx in Advance
Hi All, I am currently planning a migration from a Cisco 5508 WLC with 2800/3800 series APs to a 9800 with 9100 series APs. We are looking to install the new 9100 APs in parallel to the existing and then migrate a given area by disabling the 2800/380...
I was wanting to implement FlexConnect. I had a question regarding the best practices or recommendations regarding FlexConnect Groups.I have multiple remote locations with 1-7 APs and some campus locations with 20+ APs. We have a standard for VLANs a...
Hi! Have you encountered in WLC 9800 that a wireless user is unable to redirect to client provisioning portal of ISE? based on logs the user is successfully authenticated and supposed to be redirected but it isn't happening. This is supposed to be be...
We have a 4404 controller running on 7.0.116.0. All the ap's registered to that wlc suddenly had capwap flapping. Aps were then stable after few mins. We didnt see any issue on the switch/fw (L3 interface created). Any idea what could be checked ?
Is it possible to use DNA Spaces without DNA Center or Prime ? There does not seem to be a nice way (read , any way) of getting maps in DNA Spaces without those two. Did I miss something ? Thanks Thomas
