Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! 4 vs 6 Antenna Leads - 9120AXE
Hi All.I have a question about two different AccelTex types of antennas.Wireless design phase stated that we should use this: ATS-OP-245-8-4RPTP-36However, we only have this one model available in our stock: ATS-OP-245-8-6RPTP-36Therefore, antenna ga...
Hello,we have a printer (2.4GHz required) that can't connect to MR42. no firewall rules. below is the summary of settings. on the printer forum, people uncheck uncheck 20/40MHz Coexistence and it works out. Per Meraki support, there is no 20/40 spect...
Hi team I have some IW3702 with 4 antennas AIR-ANT2547V-N and working fine and the installation it's very simple use port 1,2,3 and 4. Now I need upgrade this access point for IW9167EH and I have quetions about the intefaces radios and antenna instal...
Good Day, User connects to SSID "DATA" via a C9800-40-K9 when said user tries to connect to this WLC URL https://*IP* (to add Hotspot Guest Users) the browser (Chrome) the browser prompt "Site can't be reached" however we are able to ping the WLC. Wh...
HI All, We have purchased WAP Model IW9167EH-Z-AP (Z Domain) for US country. could you please confirm is this compatible for US country ?
Wireless firmware versions MR 31.1.5 changelogImportant noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will not upgrade if they a...
Have a customer that we are going to be upgrading 8.5 to 8.10. In the process we are losing a bunch of AIR2602's and then adding new AIR9105's. Do we need to remove the 2602's before we upgrade and then once the upgrade is done, add all of the new ...
Hola, hemos adquirido AP C9128AXE-E y antena AIR-ANT2513P4M-N para utilizarlo como radioenlaces. Pero, hasta ahora, ha sido imposible acceder a la configuración. Por lo que hemos leído por la web, necesitamos un equipo más, un WCL, el cual que no ten...
Hi Experts How do we shut no shut or bounce AP PoE ports from WLC. Basically we have cameras connected to the outdoor mesh and we want to bounce the ports so they can get new IPs from DHCP. Cheers!
MR42 and MR46 access points running firmware MR 30.7Authentication set to WPA3 authentication.We're seeing this about 1-2 times a day on a 65 device environment. The Mac will try to connect for 30+ seconds, then will show as connected, but with no in...
Hi there,We're using 2FA for our Authentication on Wireless which is from our Azure AD and sync on the Radius Server using Custom API.I know this is a known issue with CNA of Apple when the authentication is using 2FA.I have seen also some forum with...
I am having a strange problem with my AirOS 8540 WLC sometimes using the wrong DHCP proxy IP for one of my vlan interfaces.I have a ISE enabled SSID where i have set a dummy interface in the WLAN tab.Normaly this works flawless for all the networks.B...
Resolved! Hotel WiFi Deployment.
Good day,We've changed our Hotel Wifi APs to Cisco 9120-AX with Catalyst 9800 controller. We're running into an issue where through the hallway the signal is good, but several rooms on each floor have weak or inconsistent signal strength. The APs are...
I have an Organization with approximately (5)0 9163E access points deployed across 15 networks. Though 5GHz is enabled in the RF profile, all of them have no 5GHz working. In the AP detail, they all show power level -1 and channel 36. All are on v30....
Under Network-wide / Configure / Alerts / Alert Settings / Wireless, can anyone provide hard number definitions (or percentage values, if it's a ratio) for the dropdown values when making a Client Bandwidth Usage Alert?
