Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi! I have a question for licenses MSE WIPS. Do I need to add Base Location Services and Context Aware Licences to WIPS MSE licence or you can do without them?
Hello All,When ap's are providing multi-gig performance 802.11ad, connectivity between AP and WLC would be not just ethernet right.!!! What media type we are going to use and how about the POE requirement for AP in future..?
2602 AP loosing connectivity to 5508 running 7.4.110.0.This very well could be happening during higher traffic periods-AP has been moved to another port and even to another switch-AP was even replace with a new one-Apparently there are other APs on t...
Dear All,What is the minimum software version that is required on WLC 5508 to support this ac supported ap's...?And what new feature available over 3600 series..?Thanks in advance
Hi, I have CISCO 1602 standalone access point, which has 2.4 and 5 radio and support to run on both radios. And I am trying to setup the two SSID, but first SSID to operate on both 2.4Ghz and 5Ghz radio, and second SSID to operate only on 2.4Ghz radi...
Is it possible to convert capwap to LWAPP via telnet?Through the 5508 controller, I enabled Telnet for a specific AP with capwap image.I was able to telnet to the AP and access CLI.I issued the command capwap ap controller ip address x.x.x.xThe AP di...
Hi,I have a CT 2504 controller and I have connected 1602 access points to it. They created a 300mbps wireless network that works well. I am planning to enlarge the network by adding 5 2602 access points. The users that will be connect to the 2602 aps...
Hi -I'm trying to configure two Aironet 2602e (with external antennas) to form a bridge between two buildings. I can't figure out how to get them to run faster than 54 Mbit between them. Currently they just sit at my desk in a test-setup. I think, I ...
Hi, Let's assume that it is a CISCO AP which is capable to operate in 802.11b/g/n standard. Suppose if you have legacy, very old wireless handheld scanner which runs only on 802.11b, and you have number of laptops they runs on 802.11b/g/n. If you pu...
I have a new aironet 2602 that is hooked up on POE and DHCP has issued an IP (verified by MAC). First time use. Put in IP in IE and Firefox and I cannot connect. I tried to do a telnet session as well through ethernet and ip is refused. I do not have...
Am I correct in that once Cisco MSE will do both location and wIPS at the same time? As I read it looks like there are co-existence limitations when doing this. Does anybody know what those limitations are?Also, do I have to have just the wIPS lice...
Dear GentsI'm using WLC 5508 software ver: 7.4.110.0, would like to convert below automous AP to LWAP. I'm not sure this model of AP support WLC 7.4 code. Kindly advise any possibilites to get it work with WLC. AIR-SAP1602I-E-K9AIR-AP1142N-E-K9AIR-AP...
Is there any benefit to turning on CDP for the radio interface?
All,Intermittent voice on 5GHz using 5508's and 2602 AP's, what's the best way to increase power using RRM for the TX power level on the AP's globally?What’s the best way? Using the minimum power level assignment (say 11dBm (12.5mW) equivalent to pow...
Hi AllIve set up a wireless network today consisting of 5 Cisco Aironet 2600 WAP's and a 5508 WLC. For some reason the AP's will not join the controller. I have a console connection to an AP and this is the output I receive;Mar 1 00:43:35.639: %CAPW...
