Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
HiIn a deployment with QoS configured on switches, we are going to do QoS on wireless as well (for LYNC optimization)Right now we use flexConnect on ver. 7.4.. Looking on the new AVC feature, it already have a profile for LYNC (when doing central swi...
Hello everyone!I had this topic posted to another support forum but never got a response. So I'm posting it here:I'm getting MAC flap notifications from 2 switches at our remote office from the same two switches (switch 2 & 6). There are a total ...
Hi,We have a Cisco 1602i access point that is in a geographically remote office and different subnet from the home office and network where the RADIUS server exists that we wish to use to authenticate to. The offices are joined by a VPN tunnel betwe...
While setting up the AIR-SAP1602E-A-K9 using a web browser, the AP managed to take the IP address of another device.You will need some type of software to find out what is on your network or be able to get into your router and access the DHCP list an...
I am using 1524 AP with WiSM 2 controller. The problem I am facing is I am continuosly getting messages on the core router about flapping of the access point with the management vlan. I believe this is effecting the performance of my core router as w...
Hi Cisco prime infrastucture 1.3 can make this measurements :1)Average number of devices connected to Access Point.2)Employment status of the controller licenses.3)Average distribution of the power of Wi-Fi signal at start and end of the client conne...
Hi,I'm writing a quick script to do an inventory of all the APs connected to a controller. I'm surprised not to find the Pri/Sec/Ter controller name in cLApEntry table while the IP address is there. Controller is 5508 with software 7.4.110.Where can ...
Hello,We got cisco WLC-5508 with software version 7.4.100.0.With no reason the APs (1262) started to upgrade thier firmware.as you can see in the log:Tue Sep 10 05:29:11 2013--AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:2c:3f:38:58:6...
Our controllers use the default UDP source port 32769 for outgoing Radius requests.According to the RFC, there can be no more than 256 different IDs for these requests. It has turned out that, in peak times, there are more than 256 outstanding reques...
So I ahve need to upgrade the IOS revision on my 6506-E chassis to the SXJ6 train from SXH2a. I have a 10GB fiber module I need to install plus I'm prepping to upgrade to WISM2. I attempted the upgrade on Tuesday and what i saw was my WISM1's 8 i...
Hello! PI 1.2 virtual appliance ncs process doesn't start after shutting down the ESXi 5.0 hostWe have the following deployment on ESXi 5.0 hostSmall virtual applianceRAM minimum: 8 GBHard disk minimum: 200 GBProcessors: 4 virtual CPUs (vCPUs) Before...
Hi One of my customer is using the “AIR-AP1242AG-A-k9” AP and antenna as “AIR-ANT2465P-R”Now customer want a same set up. But problem is 1242AG is EOS , the replacement is 2600 series AP.Does 2600 AP support “AIR-ANT2465P-R” the antenna or please su...
I need a little help.When enabling Adjacent Channel Rogue (Management>Trap Controls>Security), I get the following error:Error! cannot enable extended adj rogue.Why do I get this error?Reading the WLC help pages, I did not see any documentation on th...
Hello.I have a question about how to get Lightweigt AP from a wlc 4402-25 controller to a new viritual Controller.Becouse when I am shutting down the old controller the AP's don't connect to the new Controller.So do I have to upgrade every AP to new ...
We have CISCO 2504 controller and 1142 AP. Can we and how to setup different IP subnet for controller and wireless client ?Ex : Controller is 192.168.10.0/24 Wireless client is 192.168.20.0/24Thank you for your answer.Jason Chen
