Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Difference between IP learning method
Hello, I have a question about the difference between IP learning methods in wireless, when I do an AP packet capture I see that there are two methods for the client to learn an IP address (DHCP and IP snooping) even in the both cases we're using dhc...
Hello All,I am suing C9800-L-F-K9 with 17.9.3 image and trying to use both ports for C9136I Wap.WAP is connected to C9300-24UX model with image 17.9.3IssuesSwitch is configure with LACP Config and LAG is enabled on AP join profile in WLCI am seeing b...
Hi master I am not have cisco WLC for test this solution , so Can i have more than a VLAN for APs Managementexam VLAN 100 and 200 are APs management , Thanks your for reply
we have an issue that users are getting disconnected again and again and ask for password every time they got disconnected
Resolved! Error 404 ap cisco
HiI will preface this by saying that I am just recently approaching the Cisco world for work.Please bear with meI am having a problem with ap 2600 seriesA customer bought them used to install them in his garden.Then he called me for installationBut I...
Hello,I am working on starting the process of upgrading to WPA3-Enterprise. Currently we have devices that won’t support WPA3 192 bit. I do have the option to go to WPA3-Enterprise AES-CCMP128. I am currently running WPA2-Enterprise AES-CCMP128. Is ...
Hello All,we have our new mobility Anchoring setup. When we try connecting the client, the end user does not get IP.below is the debug logs-(Cisco Controller) >debug client c6:c7:a6:b5:2e:df(Cisco Controller) >*emWeb: Jan 17 14:59:17.723: [PA]Debuggi...
Hello. I am setting up a guest network on a EWC with a Catalyst 9115AXI AP, software version 17.9.4aGuest user works good, but when I try to log in with a Lobby Admin user, an error is shown. In the Access Point log, there is a log message confirming...
Hi all,We're using Catalyst 9800 cont. and 801.x peap with ldap username on one of ssid profile. Unfortunately ,some users gave their credentials to others and they logon same username/password.Is there any way to prevent this ? Best regards
I was surprised dACLs just barely got partial support in the C9800 series. The C9800 platform has been out for 4 years. Anyone working with an very old 5508 or any of the newer platforms preceeding the C9800 series had dACLs, fully functioning, inclu...
I've have mobility anchors between our company and other companyss who we have staff in each others buildings.I have 5520 & 8510s which are both anchor and foreign for certain SSIDs . External companys have 9800, so the 5520s and 8510s have teh corr...
We're using Cisco ISE version 3.2 patch 4. Cisco 5520 WLC version 8.10.183.0.I implemented FlexConnect. I'm seeing clients show up Wired and Wireless clients in Cisco ISE. The Wireless authentications show the WLC as the Network Device, NAS port type...
Resolved! Cisco AP 9115 Config Set
hello I am setting up Cisco AP 9115 https://www.youtube.com/watch?v=kW9nJ3MEZX0 I saw the link and got to SSID creation. I don't know how to set up AAA server-related settings and Radius server-related settings. I am sending the configurat...
Hi, what is the procedure to power off wireless controller 5520 appliance (aireos)? should issue the command to gracefully shutdown the unit or can directly power off the unit? Can anyone please advise? thanks in advance!
Hi, i have at a customer site one WLAN based on Meraki. Three SSIDs are configured: two corporate and one for guests. for the three SSIDs the authentication/authorization policies are enforced by the ISE (v3.3). The users attempting to get access to ...
