Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Guest Access w/ DMZ Anchor controller
I know the documentation says that the Cisco 2100 series WLAN controllers can NOT terminate a VPN tunnel and as such cannot act as the Anchor controller in the DMZ.Does the 2500 series suffer from the same problem, or can it be used as an anchor?The ...
Resolved! lightweight mode behind WGB
Is it possible to encapsulate one CAPWAP tunnel in another one with using IOS WGB in the middle? Usually after WGB we have wired clients and I was wonder if we can connect there (instead of switch and wired clients) another LAP access point.What I m...
Hi,I have some 1130AG access point and I'd like to have : - Multiple broadcasted SSIDs (because most of my clients are OSX and OSX doesn't deal with hidden SSID at all ! the clients have to enter the data each time which for WPA2 enterprise is really...
Resolved! 1140 access point. Poweroverethernet.
I have a 1140 Access Point. i notice the AC dapter did not come in the box.Maybe because it was poweroverethernet. My question is there any advantage in using ac adapter vs poweroverethernet?
Hi, We are supposed to create 4 SSIDS for staff, student and admin. The users of the three SSIDs are supposed to be inegrated with active directory.We were able to run the above process successfully, but now the users in "student SSID" are able to ...
Hi all,it's possible have two wism ( one in switch 1 and one in switch 2 ) active in Virtual switching ?
I upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the ...
Resolved! WCS Server hardware specification
Hi,WCS datasheet shows the hardware specification for the server as belowCisco WCS Low-End Server • 500 lightweight access points, 200 standalone access points, 125 wireless LAN controllers • Intel® CPU; 3.06 GHz, 2-GB RAM, 50-GB HDD (free space)I ha...
Resolved! wcs license upgrade issue
Dear all,We have two 4400 controllers which support 50 Access points each and wcs with 100 base license.Now we added 5508 controller supports 50 access points.wcs is upgraded with another 50 ap license.The 5508 controller is joined to wcs and the lic...
Hi,I'm designing the wlan solution for a client.Our requirement is to have two SSIDs along with remedy vlan(quarantine vlan).1. Corp Corporate traffic will be locally switched(Cisco wlc H-REAP mode). If software check fails users must be moved...
I have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEEFrom the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and chang...
Dear All,Our WLC 4402 and 46 1130AG Access points in LWAPP mode have been working flawlesly for the past few years, but suddenly this week some access points have not been working (but the rest are fine). They are correctly registered on the WLC, but...
Hello Eng.Can someone please help me with WLC authentication? I want to use MS IAS Radius for Management and Wireless Authentication.can please some give me configuration example through cisco site I only found example using a cisco ACS.regards,Alcid...
I want to upgrade my WISM software from 4.2.112.0 to 7.0.116.0 can I upgrade it directly or is there any intermediate release I have to upgrade to first before going to latest one.Is boot loader is bundled in 7.0.116.0 or I have to download it separa...
Hi All, I seem to be having a strange issue with my WLC 5500 and 3500 AP's. It seems that I can only have G clients working or N clients working but not both at the same time.I have WPA2 AES setup and it seems that if I turn on WMM (required or Al...
