Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Dears,Does any body have the same problem? The Samsung SCH-i569 Wi-Fi can't work at the LAP1131G with WiSM. It can associate to AP and get the ip address but about one minutes ago it had deauthentication and the phone's Wi-Fi status will show scannin...
I know you can put a minimum of 3 AIR-ANT-2422 antenna on the 1261 AP but my question is, can you mix and match antenna?Currently there is an AIR-ANT-24120 used on an older 1200 model. Upgrading to a 1261. The 24120 is 12db and 2422 is 2.4db.Environm...
I want to upgrade all my controllers (a mix of 4400 and 5508) to 7.2.103.0 from 7.0.116.0. Has anyone made this jump? Any pitfalls? Can I make that jump or should I do incremental? THankslp
we have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?thanks,han
Hi Somebody could help me, l have a WLC with locals and hreap AP´s but in some hreap ap´s the wireless service it´s so intermittent, the h reap local switching is enable and the radius server is on my head office, the problem it that every 5 or 10 mi...
hi,we have 4 WLC Wism controllers with 4 wireless wlan and 4 wired guests vlan.We are used to do daily reports of client sessions for log pourpouses and everythig works well for wireless clients.We cannot do reports for wired guests, even if we selec...
HiI want buy an Access point which cover 300 Meter coverage Area.Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.Please Help.RegardsIqbal
hi,I am using WLC 4404 and wireless is configured....I dont have much knowledge of RF.. so anyone can help me with this?There are two options in wireless tab, 802.11a/n and 802.11b/g/n.In 802.11a/n--> DCA, channels are configured as 36, 40, 44, 48, 5...
hi,we have 4 WLC Wism controllers with 4 wireless wlan and 4 wired guests vlan.We are used to do daily reports of client sessions for log pourpouses and everythig works well for wireless clients.We cannot do reports for wired guests, even if we selec...
Hello!I have some trouble with the setup of an oeap 600 ap. The ap has joined the controller as it should and the remote-lan connection to my corporate network works well, but i can't connect to the corporate wlan.When i check the event log on the ap...
Does anyone know the difference between the Backup Version and the Field Recovery Image version of the IOS on a WLC? I recently upgraded my 5508 WLC to the newest code, and the backup version is infact the previous active version I was running but t...
Does anyone have the IOS image for the Aironet 1310? May I have a copy of it please. I cant access to Cisco support today. - C1310-k9w7-tar.124-25d.JA1.tar - C1310-k9w7-tar.124-21a.JY.tarThank you very much.
this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
What is propoer sequece lightweight access point association with WLAN controller ???Did i do correct ? Please, see attached file !!!
I am managing wireless network in a convention centre which has almost 2000 APs and 28 WLCs. RF ID and location tracking enabled. In WLC I can see 500+ rogues getting detected in each WLC in different mac address. Few of these mac I can trnasilate in...
