So this is apparently the "settings" across all my networks and orgs. right now.And the slider does not go higher then 100Mbit.I will say, that when putting the slider to max, it does not seem to limit the client, but still, this is just strange, did...
Sorry I'm no expert, hope informations provided are enough :We have several PDA, several AP and several SSID.I tried to install a PDA after a problem with an APP, so I reset the device, connect to SSID of another city and...no connexion (temporarily ...
Hi All-I did find a similar thread on this error here: https://community.cisco.com/t5/wireless/lost-private-keys-after-failed-upgrade-from-17-3-5a-to-17-9-3/td-p/4908871 however, it doesn't really present a solution.Long story, but basically, tryin...
Hi All, We have Cisco 3504 Wireless LAN Controller in our network with CAP1702 and AP1832. Now we want to add few Huawei AP (AirEngine576051) in our environment im not sure if we can run Huawei AP with Cisco WLC. Thanks in advance
Please i need guidance with downloading the autonomous ios for 3500 Access point.i have checked sofware.cisco.com for the device model, i cant find specifically the 3500 series. so i know its out of support but is there no way i can still download th...
IOS-XE 17.09.02. VTP mode is Client and I can see all our VLANs on switch and 9800LF. I defined VLAN 2 with IP 10.0.3.254 /22 on Core and its routed. DHCP is from the Core and has Option 43 pointing to the 9800LF IP assigned to its VLAN 2 interfa...
Hello everyone, I have a customer that has a 3504 WLCs in HA. The Active WLC has made 2 failovers in less than a week and the System and Alarm LED are blinking orange/Amber. Acording to Cisco WLC 3504 Release 8.5 Deployment Guide, this is an Internal...
I have configured an SSID with an access control policy to block iPhone and Android operating systems. This used to work quite well to keep mobile devices off this SSID. However, it does not seem to work at all for iPhones anymore, and is not very ef...
I have a small home network. MX64 / MS120 / 4 APs: MR33/20s - all in gateway modeAll APs have simultaneously lost PoE (no lights on any of them)Switch is up and other wired ports are up I just power cycled the MS that all of the MRs are homed to and ...
Meraki Wireless 802.1x Cloud Authentication not working after firmware upgrade to MR 30.7
Trying to build a lab with wireless APs connecting to LAN and LAN to APs. I made one gateway and one repeater. I connected the repeater to a switch but when I plugged in my PC to the switch I cant get in to the network. it is saying on my Ethernet. U...
Hello,Anyone know if the CAP3702 is supported for WLC 9800?
Hi Team,I am planning to use the Cisco Catalyst 9124E Outdoor Access Point along with the Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N) and the Cisco AIR-CAB005LL-R-N Low-Loss Antenna cable. However, I noticed that...
Hello Community,,,,Let me clarify and ask about MR 36 user/connected devices limitation. I have using MR36 12APs. In this case I would like set connected devices to each APs. For eg: Only 12 users can connected to AP1 , only 20 users can connected to...
Hi Guys,I have two questions and would like some help.I currently have a WLC5508 Anchor in the DMZ for visiting users, which is part of the mobility group with an SSO-9800 (IRCM). That said, we have a project to add a Backup WLC, which would be part ...
