Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi All,Been trying to resolve an issue with WCS 5.2.130 (linux) - it is running really slowly so I moved it from a machine that was a little below spec to a VM, still really slow.... The question;I discovered under background tasks Client Statistics ...
I believe that I understand the difference between 2.4 and 5 GHZ when it comes to designing coverage to a location. I would like to know if anyone ever setup a conference room with 25 laptop’s where there is a greater concentration of device in a sma...
Hello all, With the new release of the Cisco AnyConnect(ver 2.5.4038) for iOS and the new release of iPhone Configuration Utility(ver 3.4), Do any of you know how to create a mobile config file that will allow for automatic certificate selecti...
I have to make a migration from a controller to oher.We have now in production a WLC 4406 with 90 AP in local mode and HREAP mode, and we have to change the WLC to other new model 5508.Do somebody know which one could be the best method to do that???...
Does anyone know what the "Provision Failure: MEDIATION-5, Lrad! errors are in WCS? I get this when pushing an AP template to six new 3502i series access points. The error reads like this:*** Apply Result for AP 'NameOfAPhere(C0:FF:EE:C0:F:EE)' ***...
Hi All,Just have a basic querry, What is the default mode of 1142 AP. When it's shipped from Cisco, Does it works as LAP or it can be used as a Autonomous ?Also, incase we just get it shipped from Cisco, does it have any default IP address that we ca...
Hi everybody, i am expecting an issue with my WLC 5508 with IOS 7.0.116.0. The traffic related with controler managment ( GUI and telnet access and RADIUS) is passing trough service-port.The managment inteface is connected to catalist 6513 with folo...
Is the switchport tracing feature in WCS compitable with non-cisco switches?
Hopefully this will be an easy solution for some of you.I have two LAP1041N APs I am trying to setup on a new 2100 WLC (7.0.116.0). THe APs will blink green fast; then go to a green, red, blue cycle for a min or so; then back to blinking green fast....
Hi,Currently we are running Cisco wireless AP's in an LWAPP setting with Cisco WISM. Wireless authentication for network access is linked to our Active Directory.What we are noticing is that a large number of users are connecting to the wireless usin...
Hi, As according to the cisco config example. (http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml),it says:If clients are in Webauth_Reqd state, no matter if they are active or idle, the clients will ...
have another question regarding the 1260s. If our one, 2500 controller with 1260 APs, running CAPWAPP image goes down, will those APs look for another contoller even if there are no CAPWAPP controllers to be found(only LWAPP)? And if it finds one, wi...
Hello everyone,I'm having a hard time figuring out why we lost half of our wireless speed over g radios after we went lightweight.We just upgraded from autonomous to lightweight with a 5508 controller on software version 7.0.116.0. At our venue, bef...
Is there anyway to increase the timeout value for the gui?I have an intern positioning AP's on various map's and he gets booted off the gui at random times. He isn't idle either.Thanks
ok - so, in both WCS and now NCS servers, we have a security warning becase Client MFP is not enabled, or set to "Optional". My question, and Im not a wifi wiz - what can break if I require this to be enabled? Most clients should be XP sp2 or higher...
