Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello, I am ClaudioI have problems with register the APs in the module WiSM, the AP join statistics is null.The IPs from APs are local DHCP in the module.The softtware version in the WiSM is 7.0.116. The APs are 1140. The IOS version on the Cat6500 i...
HiWe got two sites both having WLC 5508 and 20 Access Points each. Both Location are connected to each other via Metro WAN Link to share ERP and replicate Windows AD Domain / Email. Location A got 3 SSID Data SSID : DATA.EDVoice SSID : VOICE.EDGUEST...
hii have three reference 1552, 1252,1310 conect to my WLC, one of these aps is a mesh ap. i need to have only one regulatory country in my wlc. can i change the country to my air-cap1552e?
Hello,I was asked to find out what this error message means in detail; 10/18/2011 1:34 PM : APF-3-VALIDATE_DOT11i_AUTH_FAILED : *apfMsConnTask_2: Oct 18 18:34:07.181: %APF-3-VALIDATE_DOT11i_AUTH_FAILED: apf_rsn_utils.c:915 Could not validate the WPA ...
hello dears , I have 6513 which have wism and sup 720 , for some reason the access points keeps on going up and down the port channels created automatically but i cannot see any configuration inside it as shown below , is that normal ?I tried to edit...
Hi,Does somebody know or a external antenna, for example 5 or 7 Dbi, is available for the SRP521W?Thanks in advanced.Grtz Buddy
I see every once in a while a corporate laptop user coming into work, docking their laptop into the wired LAN but leaving their wi-fi switch on. Because we are serving up a open wi-fi connection in our facility (which I can't bring down), my questio...
Hello, I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is bl...
Hello I have a problem with my wcs and my controller, I have ap H-Reap mode with cisco 7921 connected to it. My problem is roaming takes 3-4 seconds to switch to another antenna but not all the time. Here is my config: 5500 WCL 7.0.116.0 / 7.0.172.0 ...
Can you please help with the followingDoes Cisco Cleanair Access points support 802.11 a,b,g,n ?
Hello,Help is required urgently. I need to clarify on recommendations of what type of access point can be used for an office. the layout of the office is thus:we have about 10 rooms in a hallway separated by walls with 5 offices on each side. i was s...
all,I'm facing a problem to upgrade my WLC 5508 from 6.0.199.4 to 7.0.98.218 On my WLC, I have a bad src error message about the SFP.With the version 6, I have the "warning" but the port is UP and Running STP Admin Physical Physical ...
Hello,Is there a guide anywhere on how to turn an AP inside an 877w into a Wireless Bridge?I have been searching for hours
Can you please hel[p with the followingWe are using 1242 AP series AIR-AP1242AG-A-K9 manged by a couple of WLC 4402.Can we add the N series Cleanair access points and manage them using our existing WLC 2204 or do we need another model of WLC ?Will we...
Hi,I have a WLC 2106 with 3 APs. Everything works and users can connect, but the throughput seem to be lower than it should (it is around 8Mbps and should be around 30-50Mbps). And all speed and duplex has been accounted for.I need help trying to u...
