Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
We recently added a controller and upgraded our access points to LWAPP. I previously used the wpa handshake timeout command on our autonomous access points to fix connectivity issues with some Intermec hand-held devices and some wireless printers. ...
I am using HWIC-AP module in 1841 router to allow wireless clients to connect to LAN. Is there a way of hiding the SSID broadcast?
Which is the cause of this message?:The AP 'XX:XX:XX:XX:XX:XX' received a WPA MIC error on protocol '1' from Station 'XX:XX:XX:XX:XX:XX'. Counter measures have been activated and traffic has been suspended for 60 seconds. What can I do to resolve the...
This is an intermittent issue I am experiencing. I have taken a packet capture using Wireshark on both a defective machine and one that works. Bascially, what I see is the Supplicant does not send an EAPOL-Start and therefore authentication does no...
I created a point to point from HQ (Root) to Office2 (Non-Root) office with the Cisco AP 1310.The problem that I am having is the VoIP phone at Office2 can not hear the other party at most of the other locations. There are a few phone that I can make...
A client connected, enable different authentication process at different times at a distance of not constant. Is there a rule? A set time? A quantity of packages delivered?See attached for more detail.Regards.MirkoS.
Hi, we have a WLC 4400. Is the following possible?:We want to have a html-site (with regulations) at which end should be an Accept-Button. After a click on that button, the user should be forwarded to the internal Web Login Page. It's equal for us, i...
In order to allow wired clients to access the wireless network, I have a device that acts as a wired to wireless bridge. This device had a wireless card and Ethernet connection. The wireless card connects to the Cisco AP just like any other device ...
We have a one location still running 3 IOS based AIR-AP1231G-A-K9 APs and 1 WDS running c1200-k9w7-mx.123-7.JA3. 1 Guest open ssid and 1 EAP-FAST ssid, authenticating to ACS Appliance V3.3. Has been working fine for multiple years until a recent po...
The alarm on Cisco's WCS is going off for the interface .11b/g and .11a going down. It also has an alarm going off with: AP 'x' disassociated from Controller 'x.x.x.x'. These three alarms are for the same AP. Whenever I go the "Alarms" section of ...
How often LAP in L3 LWAPP mode performs a broadcast DICOVERY UDP port 12223?During the boot or even during its regular operation?I saw that the AP is running the broadcast or to be more precise to arrives WLC LWAPP DISCOVERY REQUEST only when booting...
HelloI ahve 2 Cisco Wism installed on 6506-E running virtualization. when I run show wism status, the controllers are unable to get IP addresses for the service and mangt interface knowing the Vlan is there and local dhcp configured. wism service com...
Anybody know how to recover Cisco WCS Admin Password Since i forgot the same,,I have installed WCS on Windows 2000 Server.regrdsSujih RS
Configuring PEAP on IAS with autonomous aps and getting the following error on the IAS serevr so I know that the ap is talking to the IAS.Not sure what I am missing, is there some attribute I need to look at??An Access-Request message was received fr...
Hi all, I am running a 2 MSE, 4 Controller setup, all managed by the WCS server. I am trying to configure the wIPS profile. I am able to create the profiles and when I go to apply it to the MSEs I get an error message. Each MSE has two controlle...
