Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Is this possible? My colleague is not getting a straight answer from TAC.
Resolved! Impersonation of AP issue
Hi,i have a WISM with release 6.0 and 150 AP connected all in the same RRM. In the TrapLog I see a lot of |"Impersonation of AP......" messages. This issue is between AP connected to the same WISM and in he same RRM.Any idea?RegardsGiovanniAn
I am a little confused on the last two features for Guest Access Features. Anybody can explain in depth what these mean.1. LDAP Web Authentication Support for Guest Access2. Support for Proprietary Guest Access Solutionshttp://www.cisco.com/en/US/pro...
Resolved! WCS: Migration
I plan to migrate my fat APs (1130) to LWAP using WCS 6.0. The 1130 APs are running 12.3(11)JA1, will this version be suitable for upgrade?Will this version support the hostname retention?Please advise,Thanks,Colm
Why is CSSC v5 so different from CSSC v4? In v4 you could create networks and configure all kinds of settings, including specifics for EAP-FAST. I'm probably doing something wrong, but in v5 it seems like it's a watered down version of v4, a lot of o...
Hi,I have a mesh wireless solution with 1 WLC 2112, 4LAP 1522, one 8dB 2.4 Ghz antenna/LAP 1522.Software version on WLC 2112 is 5.2.157 and TX power level is set to 1, but maxim signal strenght is -65 dBm.What I make wrong?
We have installed several external antenna 1300's but this is the first with an internal antenna. Which direction is the wireless radiating? The mount that we have places the front (grey side) against a wall with the rear facing outward. Thanks.
I have with a Location manager on a WLSE 1133. The maps are showing incorrect signal coverage despite recent AP scans. They indicate that each access point can give coverage to an entire floor. A physical survey shows this is not the case. Basically ...
Cisco state; 'To participate in WDS, infrastructure access points should run the same version of IOS as the one that WDS runs.'Can anyone tell me what the effect is if the access points are not on the same IOS version? Also, what if there is a mix of...
Hi,while trying to convert autonomous APs (AIR-AP1121G-E-K9) to LWAPP mode WCS always says "Failure - Veryfying Radio role". Does anybody know why this occurs? The migration analysis summary shows all criteria as green. Thanks.
Resolved! WCS won't start after Linux Upgrade
Hi,I've just upgrade RH to v5.0 and it all seemed to go fine except WCS won't start. I was running v5.0.56.0 on RH v4.0 (I know it's not supported) on a WLSE appliance, which ironically seemed to be fine. Now I get this....Database server is runningA...
I am trying to get hreap working with local switching with little success. I want to trunk in the remote location but no matter what I do, the dhcp addresses I receive are dependent on what the native vlan is on the port the hreap ap is associated to...
Hi, I have a WCS version 4.0.97.0, and the information of the "Client Count" Report is available only the last seven days. I can to increase the number of days in the report, for example the last four weeks?Thanks
Resolved! WLSE linux service will not start
I'm troubleshooting a WLSE that will not start. Following Cisco documentation, I have use the command service WCS start. It seems like something is happening and then it says failed to start.Does any one have encounter this situation have a suggestio...
Hy,I have a problem with low power signal receive on antenna.If I stay near to antenna the signal power is to 50%.It's ok?I have 1 WLC Controller 2112, the TX signal power is set to 1.It's possible to miss some configuration on WLC?
