Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
If you have two autonomous AP's, both with the same user vlan and subnet, is there a way to block users from one AP communicating with users on the second AP.I know you can use PSPF for users connected to the same AP but need the best way to stop the...
Hello,I'M sorry, but I'm not really sure if I understand that.One SSID should see for everybody. So I need to set-up guest mode.Additionally I want to have 2 SSID's which are only seen if I configured it in the Client.I mapped to each SSID one VLAN a...
We have a WCS version 5.2.130 and WLC version 4.2.130.0Not very familiar with it. The issue here is although the WLC is reachable from WCS, I can't seems to select a profile when we want to create guest users from lobby ambassador. The WLC has been c...
I have a WLAN that is configured with multiple mobility anchors. How does the foreign controller decide which mobility anchor to forward the traffic to? Is there load balancing across the anchors or is one designated active until it fails?Second que...
I'm setting up a lab environment where I want to have a 3270 MAR connect to a 1524 MESH AP on the 4.9 Public Safety frequency and form an EIGRP neighbor relationship and perform routing. So far, I can get the MAR associated to the 1524, which is con...
Resolved! Guest Wireless Setup
Is there an example that somebody can give me to setup a guest wireless network that only has access to the internet through a vlan that does not use a wireless controller? I am looking for any suggestions.Thank you
Hello!I have ACS 4.2 and AP 1240. I`m use two SSID - guest and user. Guest ssid must use PEAP authentication, user ssid must use EAT-TLS authentication (acs user local database). All work correctly. But when i create user for EAP-TLS, i`m create with...
Hello, I have the following environment setup:- 3 Aironet AP (AIR-LAP 1242AG) in Channel 1,6,11 of radio interface 802.11b/g/n- 1 WLAN controller (WLC 2106)- Laptop with Linux kernel 2.6.27- Atheros TP-Link 54M Wireless CardBus Adapter (TL-WN510G)- S...
HelloCisco documentation mentions telnet access to AP:The controller supports the use of Telnet or Secure Shell (SSH) protocols to troubleshoot lightweightaccess points. Using these protocols makes debugging easier, especially when the access point i...
Recently two H-REAP AP's I have installed at a remote site are constantly reassociating with the controller (every 30 seconds). The WAN link is fine and there has been no changes since installation. The trap message is "AP 'UKGLRF01', MAC: 00:21:d8:7...
Resolved! 80211n with just 60 mbit per second
Hello there,we have a Cisco 2106 WLC with software version 5.1.151.0 and 2 LAP1252.Everything is enabled for 802.11n, an Intel 4965 client is connecting correctly, shows that 300 mbit per second. But the real throughput (with the iperf-tool) is just ...
HI,I have an issue with 5 1250AP standalone.The GUI (the graphic interface) doesn't work fine. Sometimes the GUI failed. The left menu, doesn't appear. (attached image).We tested with many laptops, and explorers (explorer, firefox) and the problem st...
Resolved! Client Associations
I have 2 autonomous 1230's about 25 yards apart, with computers spread out between them. Both AP's are on the same VLAN and use the same SSID. Most of the computers associate with 1 of the APs. I want to make it so that each AP has a equal number of ...
We have a WLC4400 and 12 Access points connected to it. I have the environment setup using WPA2 and EAP-TLS which all working. I am trying to make sure the wireless is locked however from outside AP's and clients. I can see a list of Rogue AP and cli...
I've search but cannot find why it will not connect on the 5 GHz
