Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi everyone,our C9800-CL controller is configured with HA, and everything appears to be functioning properly. However, I've recently observed that we're unable to view the stats of clients connected off the Fexconnect profiles. We have one local mode...
Hey all, my team and I have been contracted out by a regional MSP to perform some network moves and I have been asked to head it up as our main network guy is taking an extended vacation. I have a few questions as I want to ensure success.We are movi...
I have 3 MR52s on 27.6.One of them is connected to the wired network and it gets an IPv4 address from my DHCP server, and a valid IPv6 SLAAC address, so it's clearly seeing the router advertisements.The other 2 MR52a are meshed to the wired one.Any w...
Hi everyone, I have a setup consisting in 2 2504 WLCs (8.0.152.0) which are going to be replaced by a pair of virtual 9800-CLs (16.12.1s). While performing some tests, a couple of 2702i APs joined the 9800-CL, to set them back to the 2504, I went to ...
Hello everyone.This time, you need to establish a wireless environment using the WPA3-Enterprise security protocol.The current physical connection configuration is like this: C9500 (BB)-C9300(Middle)-C9800(WLC)C9300-PoE(Uplink to C9300 Mid SW) > C911...
What is Cisco Support Assistant Extension (CSAE)? Cisco Support Assistant Extension (CSAE) is the first Cisco Secure Development Lifecycle(CSDL) approved extension publically available in the Chrome store. CSAE aims to bring Cisco Support closer to...
I get this message when I connect my second fiber for redundancy. but I get this messageI have 2 corecore 1 port 5 to sw systems port 49 everything is fine, but in core 2 to port 51 I have problems, I get this message and it is disabled as soon as I ...
Resolved! Seeing "Unauthenticated" on Windows Nic after connecting to Meraki wifi via Windows NPS (Radius)
Seeing "Unauthenticated" on Windows Nic after connecting to Meraki wifi via Windows NPS (Radius)I am following this guide (Configuring RADIUS Authentication with WPA2-Enterprise) to configure Meraki Wifi.)Configuring RADIUS Authentication with WPA2-E...
Hi,sometimes I'm getting alerts containing IDs which I cannot find in Meraki Dashboard logs or device description which makes the troubleshooting time consuming.For example, the last alert was Clients with poor SNR with Alert ID, timestamp, node id a...
Hi,We have C9800-CL running in production, currently version 17.09.04a, I upgraded to version C9800-CL-universalk9.17.13.01.SPA.bin, through GUI, we pre-download first the firmware to the currently connected AP 9120, as you can see on the screenshots...
I have a MX67 and then 2 MR36 and I have a pair of separate networks for things to connect to. On both of them, I am getting this error message for every client. Client made a request to the DHCP server, but the DHCP server rejected the client's requ...
Problem with Guest user captive portal redirection problem. Looking for the help in WLC. Guest user -> Cisco AP -> WLC -> ISE - This problem is happening for one particular site. Other sites captive portal is working properly from the same ISE server...
'Meraki Cloud Authentication' based SSID for Guest access.Self-registration - Allow users to create accountsAccount authorization - Users must click a verification link in their email. (No need for sponsors)Let's say we advertise the same SSID across...
We need to open a few UDP ports for our 4G LTE CellSpot on a MX device
Hi,Is there a way to configure an MAC based access control on access point Meraki Go GR12 ?I was thinking it was embedded but can't find anything about this in settings.If we can't, can I use the SG350 switch to do this, only for wifi access, and how...
