Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi All,I have recently upgraded to WCS 5.0.56.2 (For Linux) and have 3 4400 WLC's running 4.2.61 being managed successfully by WCS. I'm now trying to add another 4400 Running 5.0.148 howver I'm receiving the following error in WCS when I try:"Failed...
Just now starting to poke at this- we have an open-auth network and an 802.1x network. In areas where we are more hot-spotty and a client can only see a single AP, we're getting a fair number of reports that the 802.1x network is weaker in signal out...
Hi all,I get a lot of the following syslog error messages from 3 of my 4 WLCs (two WiSMs).Error message:ethoip.c:342 ETHOIP-3-PKT_RECV_ERRORI searched at cisco.com and I found the information to use the bug toolkit or open a tac case, but I didn't fi...
The information is not clear to me. We have a couple of Cisco Wireless access point that we just bought. After running an EoS/EoL report using CiscoWorks, they show up on the list like "Cisco Aironet 1210 Access Point" as a device that has announce E...
Where can I find the documentation for this item?
Resolved! Controller, 1522 and no IP connectivity
Weirdest thing:We are trying to register one 1522 Mesh AP (the one with a Cable Modem inside) to a controller using the lastest mesh image. Here is the thing:For some reasong, the AP was previously associated to a different Controller, (lwapp command...
My company is looking at delpoying wireless in some small remote offices, we are looking at using the NM-AIR-WLC6 module in our current 2821 routers running 12.4.7d. Unfortunately our standard version of IOS doesn't support the NM. So I am looking ...
hallo,I have 2 Air-AP1242-AG-E-K9 access point.Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(8)JA2, RELEASE SOFTWARE (fc1.I'm configuring one of them to be an HOT STANDBY of the other.The HOTSTANDBY ap associates to the MAIN ap but ...
login default admin to WLSE, web CLI access interface only show none or level 0,no level 15 as I want.The WLSE was upgrade from 2.7->2.71->2.9then 2.11.
Hello, We have a 2106 ver 4.0.206.0 and 6 1131 AP's. There a 8 WLANs, on of them being Guest with Web-Auth enabled. According to the doc, Web Auth only works with IE. In our case, you can use other browsers (firefox, safari), but no authentication...
Hi there,Need help on this. Wism that deployed on the network had found issue in interface vlan overlapping. Had configured the vlan interface and assign to a group. The group had been define on specific lwapp APs. However user that manage to associ...
Does this Access Point support roaming? We want to buy 3 of theses in standalone mode and are wondering if a user moves throughout an area, if they will roam seamlessly from one AP to the other. I did not see any documentation on it so just curious. ...
hello,CCO documents said only convert back from Lightweight mode to autonomous mode.http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272Q.if customer purchaced lightweight mode (P/N:LAP-XXXX) fir...
WCS is set up and working well, 2710 is working and tracking about 300 devices. Some of the floors are a kind of cross shape, with AP's at each interior and exterior corner. I've drawn a perimeter in the Map Editor, and I thought that would limit th...
I have a WCS and when first ordered I ordered the ability for 50 AP's . We have grown and I need to add 50 more AP's and need licensing for this add.Here is what was initially ordered:WCS-STANDARD-K9WCS-APBASE-50CON-SAU-WCSAB50Do I just order anothe...
