Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Cisco suggests not channel bonding the 5GHZ when running 802.11a voice.In this case if it was desirable to channel bond on 5GHz we should deploy voice in the 2.4GHz spectrum.I assume when of if 802.11n phones are available we will be able to channel ...
HelloI have just upgraded to 5.2.130.0 on our WCS and have noticed that some of my AP already placed on maps are showing up as half green and half red. I cannot find a key anywhere that helps me identifiy what this is supposed to be telling me.Does a...
I'm running code 4.2.130 on my 4404's with an SSID running WPA/WPA2-PSK. However, sometimes on my clients it'll show connected to SSID(Unsecured Network)? I'm hoping this is a driver bug? I've personally seen it on the Intel 3945ABG's series 11.x dri...
Hi,Is there a tool to identify if I have X number of access-point I should use this controller model.So far my requirement is to understandwhich controller model supports upto 8 Access points.Do the Controller supports all AP models.StandAlone AP are...
Hi I have a basic question. The WLC can be connected to a interface of a router (layer 3 interface)? For Example:The Managment IP Address of the WLC is : 10.0.0.2, and the configuration of the interface of router is:Interface giga 0/1ip address 10.0....
Hi,We currently have a problem with our 12dBi, 2.4GHz Cisco antenna. We don't know if the antenna is defective or not. We have more than 10 1242AG LAPs in an outdoor site and eath of them has 5.2dBi antennas. We are using a 4402-50 WLC. We replaced o...
I have 2 WLc 4402. 1 Remote and 1 DMZ. I have read the deployment guide for guest access 20 times and still cannot get it to work. a couple answers that I don't see in the guide. 1. Do AP's need to be associated with the DMZ WLC? 2. Am I anchoring my...
Hi Guys, I have problem for Auto RF.I have environment with 40 AP 1131AG,WLC 4402-50AP using 4.2.130. Problem:AP no Auto Power the controller set Level power to Maximum. AP to AP interval 10 m of no obstruction. I config Auto RF by Default Can you he...
I noticed that the 5508 requires a plus license feature upgrade in order to support Enterprise Wireless Mesh. My understanding is that enterprise wireless mesh is indoor wireless mesh support. Will the 5508 support outdoor wireless mesh without the p...
According to my colluege, Cisco has a WCS planning tool that will assist me in doing indoor wireless surveys.And this tool apparently can be downloaded from the cisco website
Hi, a habe a question.I have four WLC 4400 series and WCS aplication. My doubt is:Is it possible charges (tarificador) for the traffic of users?Similarly to CDR Service in the Cisco Call Manager.
When using the map editor in the WCS the resolution of the floor graphic is extremely low and almost unreadable - even when zoomed in. When I view the graphic zoomed in under a normal map view (i.e.: not in the Map Editor) it works just fine.Any thou...
When importing maps into WCS (4.2) they look very blurry and are virtually unreadable, but if you look at the orignal PNG file (which was converted from DWG) it is perfectly clear. Is there any way around this?
Looking for a controller that can manage AIR-AP1242AG-E-K9 &AIR-LAP1142N-E-K9
Hi , I would like ask this question if you can help me:I have an AP that here version is :c1130-rcvk9w8-mx.12.4-10b.JA3When the AP with the IOS boot with the above information, it connects well to the controller.It then retrieves a new IOS is c1130-k...
