Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello,Wonder whether Ciscoworks could be used to archive WiSM configs as WCS do not have that function.Thanks,Janesha
Hi,I have lan controllers and cisco WCS. One ap is recieving this message..The AP '00:**:**:**:**:**' with protocol '802.11b/g' on Controller '**.***.***.**' received a message with a large NAV field. This is most likely a malicious denial of service...
Hi all,I'm just after verification regarding if the AP's below are capable of being upgraded to WPA2. Can't seem to find any information anywhere regarding this.Many thanksAIR-BR1310G-E-K9-R AIR-AP1120B-E-K9 AIR-AP1121G-E-K9
I;m setting up a campus LAN and I would like to use Cisco Access Points for some of my LAN deployments both indoor and outdoor. I'm new to the Cisco Wireless apart from reading about it. No practical done. I'm very interested in using the Cisco Wirel...
Can a 1520 be a root parent for a 1252 mesh child AP? I have a few locations that need just a little coverage inside metal buildings and they are in range of 1520 A freq backhaul services. Been looking around and haven't seen anyone doing this. Befor...
I have a 2006 controller currently supporting 4 remote 1010 AP's. The logs are full with the following:63 Tue Oct 11 08:11:15 2005 RX Multicast Queue FullI already have multicast disabled on it.Any input would be greatly appreciated.Thanks,Romey
Is it possible to make with a 1252 a multipoint to point connection, on central building that connect two different buildings, and what about the antenna connections, there are three connections but is it possible to connect 2 antennas one for one bu...
Cisco AP 1200 connected to an L2 switch.Version of AP 12.3(7) JA2 Spectralink phonesThe Spectralink phone sends multicast packets but the other Spectralink phones don?t see them. When making a trace on the L2 switch the packets are visible.For the Sp...
Hi All, i see a lot of Messages in my Traplog: "Decrypt errors occurred for client [MAC] using WPA2 key on 802.11a interface of AP [MAC]". Does anyone know what this means? We are using WPA2 with AES exclusively, no legacy Clients, all are 4965AGN wi...
Hi,I have tow APs (AP1242AG) that have the two radios (the 802.11g and the 802.11a radios) configured in bridge mode.Can I do this?The problem is that one of them put the radio interface (802.11a radio interface in “resetâ€. And there is no connec...
I have a Cisco 1130 AP and it can't locate the WLC. I have verified the that it's in the correct VLAN. Any suggestions?Thanks,Mohamad
I have a very simple question, that I'm a little confused about. Here it goes.Most Access Points have two antennas. One is labeled as LEFT/PRIMARY and the other is RIGHT.What is the purpose for the two antennas? When I have one antenna connected it w...
I am trying to setup a wired guest access VLAN using the WLC 4402, Does any one know if this actually works? The WLC documentation suggets it is possible but I have heard otherwise.
Hi there,I am using 2106 controller with 1522 AP and external RADIUS and web server (holding the customized login page). Everything works well for the first time when an end user tries to open a web page, the user is redirected to login page and gain...
I need a report of all the Radio MAC addresses for our lightweight AP's. Under the older infrastructure, we could get the Radio MAC's for each SSID/VLAN by SNMP query. However, now the only way to get this information is to click COnfigure -> Access ...
