Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi guys I have a few simple questions regarding guest accessFirstly do I really need to use a seperate anchor controller can I not simply route the guest vlan to a dsl connection? I have used this before but need a bit of clarity as the guest anchor ...
I have some 1131 access points that refuse to join the controller and respond with errors pertaining to country code problems. The problem seems to be a hard one to nail down since I have installed about 75 of these all from the same shipment but onl...
I dont think its possible but I vaguely recall seeing a document stating that it is poosible to have two SSIDs on a single VLAN.If so can they also have two different authentication methods
We have the cisco 1841 cisco router and its having 2 ethernet ports . 1 port is connected to LAN and other port is connected to wireless box.I want to configure the bri as a back for the ethernet port.can anybody help out on this.
Hi,How can i determine the type of license that i'm using on a WCS?How can i distinguish Standard from Location based?Thx.
I have received a certificate(pem-file)from Globalsign.Do I have to combine this into a pkcs12 file first, or can I upload the pemfile from GSign right away ?And, if there is something wrong with the certificate, how can I then access the controller ...
I want to use Cisco 1250 Series LAP (E ETSI Regulation) wireless n at 2.4 GHZ and (total 3 lap access points the total area with wireless controller of 2112 series) with wireless n in a warehouse of 90 meters by 70 meters area.question 1.Can Connect ...
Have the requirement to be able to specify the channels that are being used with a 1252. Seem to be able to do this with a US based 1252, but the European version seems to only want to use DFS.Is ther a quick way to disable the DFS function and speci...
Hello, We have several 12xx AP's running fine c1200-k9w7-mx.123-4.JA2 . After upgrade one of the AP's with c1200-k9w7-mx.123-8.JEC2, most of clients cannot connect (even Cisco/Linkys WET's). Another strange observation - with JEC2 CPU usage jump to 9...
Hello!I upgraded 1121 to lightweight with upgrade tool.Now I want it to be joined to 2106.In debug packet I see that 1121 sends discovery request (broadcast, or, after I addedd dns record unicast) to 2106 and 2106 replies. Then there is no join reque...
WLC 4402 connected to 4507 switch.GBIC1 connected to a gigabit port on module 3 of the switch; GBIC 2 connected to module 6. LAG is enabled in the 4402 configuration.I've recently reworked some VLANs, essentially to move workstations and servers off ...
Hi,I have a Cisco 877w router and I'm sure it's not configured correctly by me. If I cable into the router things work fine like the internet and connecting to work etc, however if I wirelessly connect it is never as reliable, it becomes slow etc.Jus...
Does anyone know if the 1500 series which are presently 802.11b/g AP's will be somehow upgradeable to 802.11n AP's. We are very close to putting in a 1.5 square mile mesh system.
Every day at least once and sometimes twice, I have several access points that reboot. They all do it at precisely the same time and it is usually the same AP's - about 8 of them. I have other access points that do not go down.Any ideas? Could this b...
I was told by a wifi tech that the "pipe bomb" antenna [air-ant2506] should be installed upside down when installing inside a building, ie warehouse.When I go to the hardware installation page for the antenna, Cisco makes no statement regarding this....
