Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
When I enable WLAN override for a specific AP, and I select only 2 of the 5 avaliable WLANs, all SSIDS disapper for that AP. My WISM is running code 4.1.171.0. Does anybody know if this is an issue. The AP is an AP1131.Thanks for your help.
Hello all,Can I use AP1131AG for air relay?Here is the scenario:--wired--AP1131AG--wireless--AP1131AG--wired.Thanks.
What would the estimated output power level be when using a 1242 with rubber ducky antennea in warehouse be to get 1 1242 per 8,000/sq ft for use with 7921Gs?I'm guessing 6mw-12mw? I'm guessing that at 50mW I'd have way too much power for 1 1242 per ...
DearsI have 4 WLCs,3 are active and one is backup Controller with AIR-LAP1522HZ-E-K9So mesh technology i need i-e- One Rap will be connected through ethernet and 5 MAPs will be through wireless with 100 meter radius and start topology.RAP will be in ...
I am trying to get our Cisco 1130 AP's to use Radius MAC Authentication using a freeradius server. We have been successful with other AP's (Proxim, Netgear) but haven't been able to get the Cisco 1130 to work. I have attached 2 files. One is the runn...
HiWe are planning to implement a wireless network with Cisco LWAP 1240AG AP's with Cisco AIR-ANT4941 antenna.I understand that you should have AP's around the inside edge of the building spaced between 8-10 metres depending on the survey and then wor...
Hello,I have a 1130AP and try to associate the AP witha WLC at a remote site. The AP grab an IP address and resolved the Cisco-LWAPP-CONTROLLER to the IP address of the WLC. I could ping the WLC from the AP cli and vice versa. However the AP is not g...
Hi All,Just a quick one. If this timer expires when using web-auth on a guest wlan in the following wayPC --Ap -- WLC (campus) -- Anchor WLC (DMZ) --- wwwDoes the web session break and the user will be redirected to the web authentication page?Many t...
I have a Location 2710 that was being seen by the WCS.It worked fine for almost a day. But strangely it started to being not seen by the WCS.I tried to associate again the 2700 with the WCS but I received a message from the WCS:No response from Locat...
This is my first wlc upgrade. I have 2 4402s with 12 AP1242s lwaps split between the two controllers. What's the best practice in upgrading the wireless lan controllers? Should I power one controller off while I upgrade the other or keep them both on...
For a stand-alone access-pointIs there a limit for maximum number mac-adresses?
I want to enable wirless connections for data transfer from boats when they arrive in port. I'm thinking of using a mesh network to cover the quay areas back to the main office and either use mesh nodes or access points on the boats themselves. I'll ...
I have a brand new installation of Cisco CCM 6.x and Wire controller 4402 with 11 AP's , we are using both wired and wireless phones.What is the proper switch configuration for QOS on the ports Ap's are plugged into and also for Qos between switch an...
HI,I am using cisco 1812W router with IOS c181x-advipservicesk9-mz.124-15.T7.bin.I am running this router as a DHCP server with pool of 10.0.0.0 / 24. The wireless users connecting to this router gets authenticated by ACS.Once authenticated, they wil...
I searched for my mac address in WCS and I recieved three results. See the attached screenshot. I am just curious why the second entry show I am associated to AP 00:00:00:00:00:00?I do not have an AP named that.Running 4.2.130 on all my WLC. Have a m...
