Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I was running 4.2.130 on my inside controllers, and hadn't yet upgraded my Guest/DMZ Anchor controller to 130 yet, it was running 4.2.99.I upgraded the ER to .112 as recommended and then the controller to 4.2.130 and DHCP responses were then getting ...
Is there a way to run a report that specifies exactly how many 'Clients Per AP' were in use for a particular event. I was able to run a report on TOTAL client count which displayed a graph but thats not what I need. The event occured June 10, 08? I a...
Hello all,so as the Cisco RRM document states :"The TPC algorithm is only responsible for turning power levels down"but on the calculation criteria, it says "If Tx power needs to be increased: TPC hysteresis of 3dBm must be met"http://www.cisco.com/e...
Hi there,I receive this Warning message in WLC version 5.0:Warning: Our AP with Base Radio MAC 00:1f:6d:b9:48:d0 is under attack (contained) by another AP on radio type 802.11b/gSo, what does it means? Can someone explain..Great Thanks.
We have a 4404 controller here, and would like to set up a a small remote office with wireless using our controller. The issue is being able to keep the same SSID at the remote office as we have at the central office without having the latency of mul...
I am trying to use 1522 as a point to multi point bridge. I can use only 5Ghz antennas in this case. I can remove 2.4 Ghz antennas in this case. Is this correct?
I am configuring the Access Point and after going through the Express Setup and Express Security pages, and after turning the radios on, the Services page no longer displays HTTP, or any other services. It does however display the following..." \n'; ...
Hi Sir,I know from the fact that the wireless LAN controller has a standard signatures for IDS. Is there a need to update the IDS signatures since new attacks can be found every 3 to 6 months? If yes, where can I get the latest signatures IDS downoad...
GreetingsI have an old 1242 AP that stopped working. We RMA'ed it and jsut got the new one. I placed the old config on the new AP and cannot get it to work. I do not have access to the GUI so I am consoled into the device. We can ping out from the co...
Hi all, I see in my syslog on the WLC an error and I don't know what it means.Jul 08 15:08:46.975 spam_lrad.c:2442 LWAPP-3-REBOOT_ERR2: AP 00:1f:9e:d6:00:f0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason: UNKNO...
We have successfully been managing all our WLC's via WCS. Last week one of the 6500 WiSM Controllers stopped responding to config refreshes from the WCS. When re-freshing the WCS config from the controller got the error message - failed (see logs). R...
I have a client that sees and attaches to a 1242 AP but is unable to get an IP address from the DHCP server via the AP. It returns a msg. saying Limited or No Connectivity on the client. Does anybody know what may be going on? Is this an AP issue or ...
Is there a Cisco GIG Ether Power Injector Available
Hi allCurrently i am using WLC,WCS and LA.Right now i am facing problem of Rogue AP.I know his mac address as well as vendor but how can i know his exact location.I am using Netstumbler tool.Please reply
I have a WLC 4404 running 4.1.192.22M(Mesh). I have 20 1522's currently and all seems to be working great until I try to connect a client through a bridge device. The end device cannot obtain an IP address via DHCP, the request goes out, but the resp...
