Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi all,Following the latest update, some of the APs have unexpectedly transitioned into repeater mode. Despite performing reboots on the affected units, the problem persists, with the APs persistently acting as repeaters.This deviation from their pri...
Hello All, If I have a to use only 2 antenna AIR-ANT2547V-N-HZ= on antenna Port1 & Port2 will the AP function with dual band or not ? Or as it has 8 antenna ports, how many antenna are mandatory to use if using antenna model AIR-ANT2547V-N-HZ? Thank...
Hi, I have issue in implementing privilege level command for non-admin user on our C9800-CL. We have 3 types of users: - Super-admin level: it is level 15 - Admin level: it is level 7 for L2 support to do some users deauthentication, adding some comm...
Hi, recently I bumped into problem, laptops with windows 10 and 11 that cancelled to connect WiFi. I have ISE 3.1 with connection to Windows AD and from ISE I can see this error. Failure Reason 12511 Unexpectedly received TLS alert message; treating...
Hi We setup HA in C9800 with version 17.3.5a, and got error message with command show chassis. Please see the below. Does it miss some step? Thank you ABC-WLC#sh chassisChassis/Stack Mac Address : 0822.2222.2221 - Local Mac AddressMac persistency wai...
Dear All, I got a question on some networking issue on meraki switches setup, below are the SSIDs that i use in one of the network profile in meraki dashboard, for switch port 7 & 8 i can specifically assigned with allowed vlan 113,213-214 rather tha...
Dear All, What are the different between Gateway AP and Repeator AP ? Keith
Should I be able to use wpa with psk ssid on a flexconnect AP when it's derigestered from wlc? What is the expected behavior for already connected users VS new sessions?
I have 3 wlc9800 as below: 2 in SSO and third is configured as N+1 Am testing ap backup primary option under ap join profile , so i configured an ACL on switch to prevent communication to primary controller then ap successfully registered to N+1 bac...
Hi, We have concerns about the use of an SSID dedicated to production, on which are Raspberry pi connected in 2. 4GHz.Users use Raspberry pi to connect to remote desktops, and the slightest disconnection cuts off the session, which sometimes happens ...
Dear All, I would like to ask how i can add my Catalyst 9200 switch into meraki dashboard ? does it needs a dnac license in order to do that ? Best Regards, Keith
Hi Folks,I try to find Meraki AP with frame rate of 2.7 Gbps*, with up to 2,402 Mbps in the 2.4 GHz (roughly) band and 287 Mbps* in the 5 GHz (roughly)For MR44 and based on the datasheet it supports: “frame rate of 2.7 Gbps*, with up to 2,402 Mbps in...
Hello we have trouble with access point C9120AXI-E when they are connected on "c9200L PoE+" ports.WLC 9800: IOS Version 17.9.3 (VID 5 and 7)C9200L Poe+: IOS Version 17.9.3 Cupertino (same issues with 17.11.01)In the access point guide, i've find the ...
how many users can connect in one access point with how many meters coverage with omni directionmodel # Cisco 9166I
Hi all,I currently configure wlc9800 with 4 ssid on it. In one of the wlan I use radius server for domain users to authenticate but I need to restrict them to connect only with their workstation laptops or tablets. I have all wlan MAC addresses avail...
