Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, We have 2 Cisco Aironet 1300 wireless bridges with yaggi antennas. The connection drops sometimes (every 2 or 3 days) and never comes up again. When we reboot the non-root bridge the connection works again. We swapped the complete unit but still ...
I have a pt-to-pt wireless bridge consisting of two 1410 bridges operating over a 7 km link. It worked great until after approx. 2 weeks of operation it suddenly went down. The ethernet uplink led on the root's power injector was off with green inje...
Resolved! how to send WCS alert?
Hi forum,How do i configure the WCS to send alert to syslog server or send via emails?Thank you,paul
when i failover from the primary controller to the secondary the AP Group Name shows none even though it was on the correct AP Group Name on the primary.
I am checking a couple of 1310 Bridges. I am finding that some of them won't associate. I have setup a test lab and when I test I get most of them to work and some not. I made sure that the SSID, the WEP-40, encryption and radio mode is set correc...
Customer wants to have users on their guest WLAN get redirected to an acceptable usage policy page without having to authenticate when connecting to the network. We're using WLC4400's. I know it can be done using external elements, but can the contro...
Hello all,Hoping you can help me with the following issue. I have no experience setting up a wireless network, so bear with me.We have a network where 9 office floors are connected by access switches [Catalyst 3560] to 2 core switches in the server r...
Is it on the roadmap to have one managment platform for both IOS & LWAPP based AP's If so when will it be out . Will it be on the WCS platform ?
Resolved! Separating multiple WLANs
We have several 1010 and 1242 running LWAPP controlled by a 4402 and WCS. These are spread across 3 sites (A, B, C). We also have 3 WLANs (X, Y, Z).My question is: Can Site A have only WLANs X & Y, Site B have only WLANs Y & Z and Site C have only...
HelloIs there a document that can help me understand how to go about getting a WLAN installed, and explain what backhaul, omni etc acutally means, how to choose the best antennaes..etc?TIAShervan
Resolved! 1131AG CLI commands
I am attempting to reset an ap to its defaults. I can get into the cli, but the "wr erase" command is not available. How do I erase the config on this ap?Also, I originally configured the ap to connect to wlc 4400, which worked great, but when attemp...
I'm new to wireless and having some issues trying to set up our WLSE Express (firmware now upgraded to 2.13.1u and talking to 1130AG Aironet APs) to authenticate clients against an LDAP server.Internal authentication against local Users on the WLSE E...
Guys,I'm guessing this AP is part of the batch that shipped with MICs installed.I've flashed this to lightweight but the .csv file is empty.The log mentions that "MIC is already configured in the ap".LOG Details2007/01/11 10:22:52 INFO xx.xx.xx.xx...
How many Cisco wireless access points are recommended per Cisco access point?i.e., a 1100 series AP
WLC 4402 w/ 4.0 codeTopology: Router (gateway) with two subinterfaces, 192.168.1.254 (main vlan) and 192.168.20.254 (guest vlan)I've created a guest WLAN - 192.168.20.0, using web authentication. My wireless client sees the WLAN and obtains an addr...
