Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

We are converting to an LWAPP wireless network from autonomous.One building with 16 APs has an SSID that we only want to exist in that building.How do I restrict an SSID so that it only exists on specific APs?So far I've not been able to find a way t...

I have a vendor that will be putting a PC on our network. I would like this to be wireless but the Vendor will not give us Admin access to the PC and we will definitely not give them our wireless passwords. Is there a wireless solution for this scena...

gkdany by • Community Member
  • 982 Views
  • 2 replies
  • 0 Helpful votes

I'm proposing the WCS version 4.1. And, I have some questions. Is it possible to accumulate the event log of APs and a Controllers to arbitrary local folders periodically? If possible, please teach me a method. Is the event log of an APs and a Contro...

Hi, We have a WLC 4404 and had a dodgy Gbic that caused the port to go down, but now we can't get the port to come back up. Do you think reloading the firmware will reset everything?Thanks

mbhnt by • Level 1
  • 829 Views
  • 1 replies
  • 0 Helpful votes

Has anyone looked into wall-mounting an Aironet 1250? We do not have ceilings in most locations which we can hang APs or antennas from, so I'm at a loss for how exactly we're going to use the 1250.

jpolczyn by • Level 2
  • 1954 Views
  • 4 replies
  • 0 Helpful votes

Greetings,We have a BES behind an ASA5500. We've discovered that when a Blackberry user is the first to authenticate to the Internet via the BES - every subsequent BB user are not authenticated during the absolute time-out period - then the cycle beg...

iholdings by • Level 5
  • 472 Views
  • 0 replies
  • 0 Helpful votes

What wap commands affect the radio transmit power ? Is it power local cckpower local ofdmAre these the "B" and "G" settings?Also what is the command for the "A" radio power settings ?

glen.grant by • VIP Alumni
  • 1096 Views
  • 1 replies
  • 0 Helpful votes

Greetings,I have a small network that uses 1242 APs for clients machines. Our wired WAN link can be unreliable, so I would like to configure one of the 1242s as a bridge and connect it to one of the many wireless networks we have in our neighborhood....

IM-Design by • Level 4
  • 1181 Views
  • 2 replies
  • 0 Helpful votes

Hi there can anybody guide me whether i can connect one cisco access point though wired connection. and rest of the access points will be aquiring the ip address from the wired connected access point without using any wired connectivity? Is it possib...

shripad.s by • Community Member
  • 678 Views
  • 2 replies
  • 0 Helpful votes

All,I'm in the process of a demo/protoype using the cisco lightweight products (4402 controllers w/ 1240 LAP), and using Air Fortress gateway for Layer 2 authentication...I have 3 lightweight AP's associated with the controller (running in Layer 3 mo...

davishw713 by • Frequent Visitor
  • 2345 Views
  • 7 replies
  • 0 Helpful votes

Hi,I am ruuning WiSM 4.2 and all APs are running with RRM. What I find is that sonme APs go as low as power 7 when in fact they should go to a min of 4 (the power setting I used for my site survey).Is there a way (gui or cli) to force RRM to a "minim...

Hello all,I am installing 1252 AP's for the first time later this week and can not find on Cisco's web site what to enter for the dhcp option 60 vci string for this model AP when using IOS as the dhcp server.Will "Cisco AP c1240" work or perhaps "Cis...

bmack by • Community Member
  • 1405 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card