Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I'm trying to adjust the TX power on my access points so clients get connected to the closes AP when they move and do not get stuck to a single one. I adjusted the TX power using a RF Profile between 8 - 14 dBm, but after a while I still see some of ...
Resolved! Firmware Network Issue MR30.5
Hi together,we have a bad condition with MR 29.6.1 → MR 30.5 on AP MR36 ....Let's try to describe:We have 100 AP's, MR33, 36, 55 ...In some classrooms we didn't have enough RJ-45 plug near the beamer/projector, so we had used network Splitter. (1)Th...
Hi,I have "Failed Authentication" with this client: da:0e:xx:yy:zz:aeA pcap file indicated a bad AP which try to reply: e6:cb:bc:ff:gg:hh but this bad AP mac address is not in a rogue AP list.My legitimate AP has this MAC address: e0:cb:bc:ff:gg:hhHo...
Dear Cisco Support Team, I hope this message finds you well. My name is Kashif, and I am currently working on configuring the Cisco AIR-CAP3602I-N-K9 device for our network infrastructure. I am reaching out to seek your expert guidance and assistance...
Resolved! l have AP-2802i-e-k9 l need configure
Hi l have alot of cisco AP-2802i-e-k9 l want configure then without controller and l want also setup wpa3 enterprise it is possible???
I HAVE AN IPAD FOR THE SELLERS IN MY STORE, I CREATE A HIDDEN SSID FOR THEM TO CONNECT BUT EVERY THEY ADD IT THEY LOG IN WITHOUT PROBLEM, THE PROBLEM IS THAT WHEN IT IS TURNED OFF AND ON AGAIN IT NO LONGER CONNECTS AUTOMATICALLY AND I HAVE TO ADD EVE...
Resolved! WLC 4402 question
We have a WLC 4402 and I want to know if I can reboot all my AP's without going to touch each one at each site? I see an option under the Wireless tab, click on an AP then I see "Perform a hardware reset on this AP" will this just simply reboot the ...
Hello,I've setup radius for admins to logon to our 9800 (with ISE) but when I logon to the web admin portal I cant see any admin options. Just Monitoring and Dashboard.CLI seems fine.This is whats setup on the 9800:aaa new-model aaa group server rad...
We are currently using MR32 as our access points and we have configured a Google OAuth for access control of one of our SSID. We have also configured splash page frequency every thirty days under splash behavior section. We have noticed that users ar...
Hello Team, Is it applicable to convert 1700 series or 1600 series AP to standalone and configure it to authenticate with Radius server?It would be appreciated if there is a document or a guide that describe how to configure it to authenticate with t...
Hello,I enabled RSSI low check for 5Ghz and 2.4Ghz, for 5Ghz set to -67 and for 2.4 set to -65but why on the client i can see there are still many client with rssi lower than -65 and 67?
We are experiencing loss of connection of Barcode devices after migrating wlc AireOS to C9800. I've tried using only 2.4G, disabling FT, disabling Clean Air, changing session time and idle time but it still doesn't work. Please help me. Thanks.
Hello,I'm configuring an EWC on my cat 9120 AP.When I finish my configuration, how can I configure a second EWC for redundancy?Is it enough to just connect a factory new EWC to the network like I used to do with Mobility express access-point?TksJohnn...
Hi,After upgrading WLC-9800 from 17.6.5 to 17.9.4 license showing not in use. When the WLC was in 17.6.5 we can see the Essential license, but when we upgraded to 17.9.4 there was no license showing though smart license is enabled.though it showing ...
I have had reports for slow/ disconnecting WiFi Clients ( smartphones ) at one of our remote sites. When testing connection on site, SNR looks ok and Signal strength looks ok ( see below output) . Connections to Wireless LAN and Cisco switch inte...
