Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Newbie: Indoor antenna ranges

Please excuse a newbie on radiowaves, antenna, dBi and stuff like that. Is there a "simple" way to calculate the range (in feet or meters) for a antenna and are there any tables for how much a wall dampens that range ?For example: To me it seems lik...

Recover from corrupt IOS Image on 1230

Hiis there a way to recover from a corrupt IOS Image after upgrade von 12.0.8 to 12.0.11 on a 1230?I get the following and need to recover or send the image again into flash.---cut---Loading "flash:/c1200-k9w7-mx.122-11.JA/c1200-k9w7-mx.122-11.JA"......

adieball by Beginner
  • 1037 Views
  • 1 replies
  • 0 Helpful votes

PCM350 can not Associate with AP

Hello all, I have a troublesome PCM350 PC card that can not associate with any AP's. All troubleshooting steps followed. Is there a way to set the card to factory defaults. Or does anyone have any other idea before this hits the graveyard.

tlchant by Beginner
  • 226 Views
  • 2 replies
  • 0 Helpful votes

Can I not use ACU to authenticate via LEAP?

We are investigating a solution to provide wireless access to public places. It is kind of not practical to require the client user to have Cisco ACU software in order to configure LEAP on his wireless card. Does LEAP work without the ACU software on...

pambosch by Beginner
  • 309 Views
  • 1 replies
  • 0 Helpful votes

configuring NTP on AP1100

Hi!I try to setup an AP1100 for getting the time from an W2K Server via NTP .But it will not work. I did the same with an BR350 and same W2K server, this works fine. Any Idea?Than you,Rouven

LEAP over LDAP, ca it be done?

Dear SIr,Can LEAP support single login to windows via LDAP? I read through an article published in Cisco website saying that LEAP only supported in Windows NT/2000 Active Directory.What is OTP, one time password compared to single login password?CSAC...

c.ong by Beginner
  • 323 Views
  • 1 replies
  • 0 Helpful votes

Managment VLAN - SSID mapping

I'm implementing a large WLAN for a hospital. they will be using Cisco VPN and RSA OTP to provide authentication and data confidentiality/integrity. They also desire a Wireless LAN Solution Engine.I wish to create a "user" VLAN-SSID mapping, and a ...

ED CARMODY by Enthusiast
  • 726 Views
  • 6 replies
  • 0 Helpful votes

AP1220 DHCP Service

I have a bit of a conundrum, I have a client associating to an Aironet 1220 unit, the problem is - the client appears to have a DHCP server on his side, and to have plugged the bridiging unit (A Smartbridges Airbridge) into the ethernet switch. The i...

plates by Beginner
  • 349 Views
  • 1 replies
  • 0 Helpful votes

WGB - Password settings

Hi,We installed a WGB 20km away and forgot to configure password on it.Could anyone tell us, how to configure remote a password onto the WGB to secure the http-access?thanks ins advanceAugust

asarkany by Beginner
  • 218 Views
  • 1 replies
  • 0 Helpful votes

Private VLANs and WLANs

Has anyone implemented PVLANs on a large wireless LAN network to limit broadcast traffic? It is expected that almost 100% of the traffic will go off the VLAN to different subnets so intra-VLAN traffic will be minimal at most. Without having tested ...

jehuffman by Beginner
  • 241 Views
  • 2 replies
  • 0 Helpful votes

Can AP connect to a wireless bridge with root off

A 340 wireless bridge which is configured as an access point mode can be connected to 340 wireless bridge which is operating as bridge only mode with the root mode is turned off.WEP is turned off. No MAC filtering enables. Both SSID are the sameHowev...

c.ong by Beginner
  • 346 Views
  • 3 replies
  • 0 Helpful votes

AP 350 Complete Factory Reset

I need a way to completely reset the 350 to a factory default config. The buttons on the web interface do not do a complete reset. My vlans still exist after the reset, and this is not desirerable. I'm sure there are other settings still hanging a...

sfeldmann by Beginner
  • 780 Views
  • 4 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: