Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi all,I am experiencing an issue with 2x C9120AXI access points.They are reloading every few hours with no time patternsThey are displaying a "power Imax error detected" error message on the switch (see below)They are connected to a C9300-48U switch...
Two WLC 9800 N+1.Enable AP Tag Persistency is enabled on both controllersIf I set a Policy Tag on an AP and write the tags to the AP when it is joined to WLC 1, and it then joins WLC 2 it will keep the tag setting. If I then set another tag on the AP...
Interesting antenna connectionsI saw this picture on linked in and thought it was interesting...The way the antennas are connected is not the way I would have done it. Each antenna has 1 x 2.4 and 5 Ghz radio connected. I was trying to visualize what...
Resolved! Both SSIDs is not showing in wifi
Dear,we have facing some issues related Wifi ssid we have two ssid configured in our controller wifi-guest(vlan1008) or wifi-User(vlan1009), but still showing Wifi-guest & proper internet working. so guide about second ssid.Regards,Muhammad Sufiyan
The 9800 wireless controller failed to classify devices, causing the wireless air interface scheduling optimization to fail. 9800CL#show install summary [ Chassis 1/R0 ] Installed Package(s) Information: State (St): I - Inactive, U - Activated & Unco...
Hello, Everyone.I was recently browsing through the internet in search of a new fast AP that is able to wirelessly bridge to my non-cisco wireless network and I began reading about the features of the Catalyst 9130 AP. Then I came accross this docume...
Resolved! 9130 AP, New out of Box, Jumble CLI
I have a recently received RMA replacement, new out of the box 9130When I try to console in, I see this jumbled textI am using COM3, 9600 and I just done working with 7 other APs the same way which were perfectly fine. I tried the reset button, etc.T...
i introduce anchor controller in network for guest traffic this anchor placed in DMZ - modle C9800 Foreign Controller is already placed in Data center for User traffic. i understand Mobility tunnel and capwap tunnel sever different purpose on diffe...
AP 2800/3800/4800/1560/IW 6300 gets into a loop after attempting to join WLC with FIPS enabledIt dosnt work for us to reset the AP. Still looping. We have a lot of 2800, only one happen so far. Is it possible to do anything else?
Hello Communityi've amazing misbehavour with scenario where i need to restrict vast majority of clients of locally switched SSID toward sensitive subnet while allowing specific clients to access this subnet. for this to work i've configured ACL denyi...
I have a Cisco 2602i that will not join a Cisco 5508 WLC.When I watch the AP start up from console I see these messages:*Jun 13 16:55:09.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller*Jun 13 16:54:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection ...
Hi, I am facing a licensing issue in Cisco Software Central / Smart Licensing and would appreciate your guidance. According to the BoM and licenses purchased, the environment should be using, AP Perpetual Networkstack Essentials. However, in Cisco So...
We have a C9800-40-K9 running version 17.9.8. We have several C9136 APs joined. The second 5Ghz radio on the C9136 APs are down and say we need to upgrade the IOS in order to enable the radio. What is the minimum code required for the second 5Ghz rad...
Resolved! Precautions when replacing MR to CW9172
We plan to replace the MR with the CW9172.MX provides cold swap guides, and attention must be paid to port mapping.Are there any precautions when replacing the MR series with the CW series?
Resolved! Licensing question
Hi, have licensing question. I have 2000 DNA advantage license that expired in 2027 and system running on 9800-40 controllers. upgrading 500 old APs currently using DNA advantage licenses to Wi-Fi 7 APs, do I need to purchase 500 unified licenses for...
