Whats the default AP license capacity for AIR-CT3504-K9 - Controller? Do i need to upgrade my controller with LIC-CT3504-UPG before adding LIC-CT3504-1A licenses.
Whats the default AP license capacity for AIR-CT3504-K9 - Controller? Do i need to upgrade my controller with LIC-CT3504-UPG before adding LIC-CT3504-1A licenses.
Dear Community, Please kindly need your advices, can Aironet Access Point such as 3501, 2702, 3702 join WLC 9800 series? do they only need buy AIR-DNA License or do they need extend their warranty first and buy the license also? Any suggestions are a...
Hi All, I have setup Telegraf to collect data from cisco 9800-CL on vmware, then send data to influxdb, everything connected and data tables has shown in influxdb but with no measurements in!Anyone has idea if the cloud version support grpc Telemetry...
Hi NetPro,anyone know the below error msg stand for ?AES-CCMP TSC replay was detected on a packet (TSC 0x1C07) received from 001b.7709.0301. your reply will be highly appreciated.regards,Jackal
Dear All,I have a Cisco 1815i AP with mobility express installed. I've been noticing lately that its transmit power is low (3 dBm) where other APs have 18 and 20 dBm. In addition, coverage area is small.Although this was working normally before, but ...
From AP:cisco C9120AXI-B ARMv8 Processor rev 0 (v8l) with 1875204/1065904K bytes of memory.Processor board ID FJC26381AZTAP Running Image : 17.6.4.56Primary Boot Image : 17.6.4.56Backup Boot Image : 0.0.0.0Primary Boot Image Hash:Backup Boot Image Ha...
I have 2 x 9120axi EWC APs & i cannot get the day 0 configuration to work. They are both running version 16.12.04a & i go through the setup procedure where prompted to input the ip address for the interface, subnet mask, default route & username/ pas...
Have a customer with all APs already associated to their main vWLC running 8.3. Created a new vWLC to act as their secondary controller. Statically assigned WLCs in HA tab for all APs. None of the APs will join the controller. APs are 3602i, 3702i, a...
Hi, I am struggling to configure my AP model air ap2802i-e-k9after booting the I keeps on displaying the following:And when I try to go on to config t mode It does not allow me.Please help....!!!!
running 17.3.6 on C9800.i attempt the do the above but unsuccessful.check online Cisco Doc - 17.3.x - disable HA.Disabling High AvailabilityIf the controller is configured using RMI method, use the following command:no redun-management interface vlan...
After "Clear stats on all AP" joined APs are not appearing
I've tried different channels and different channel widths.I've looked at radar event counters, but they're not incrementing.I've run my config through the wireless config checker.Interference and noise aren't terrible and I have a terrific SNR.Yet t...
Hi,I would like to know whether the ff: AP's could run on Autonomous mode bu either means of a firmware or other method and non reliance on the controllers.AIR-CAP3602I-N-K9AIR-CAP3602I-N-K9AIR-CAP3602E-N-K9AIR-CAP1552E-N-K9thanksSent from Cisco Tech...
hello I have a problem.I try to join an ap 2802 to a wlc 5520 but I can't do it I get the following error in APIN AP 2802:show capwap ip configIP Address : 192.168.240.234IP netmask : 255.255.255.0Default Gateway : 192.168.240.3Primary controller IP ...
Hi! I have install an c9800-CL in AWS the only release to install was 17.6.1 so I do so.But I need to downgrade it to 17.3.4 because we have 2702 APs.I run the 17.3.4 bin file and everything looks right under the installations the WLC reboot but came...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-21-2025 01:47 PM | ||
05-13-2025 10:37 PM | ||
02-27-2025 06:05 AM | ||
02-18-2025 11:22 AM | ||
02-13-2025 10:43 PM |
User | Count |
---|---|
11 | |
11 | |
2 | |
1 | |
1 |