Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,Is it possible to trunk the wireless connection so that we can put VLAN over the trunk. The VLAN's must be separated so on device in the VLAN 2 may not communicate to the VLAN 5 and vice versa.Thx,Marc
We have a Aironet 1200 currently configured for wireless data access. Our Telco team wants to add some WiFi phones, which will need to be on their own VLAN for security reasons. I've added the second vlan and SSID to the AP, but where I'm having the ...
We are looking to upgrade from autonomous access points to lightweight access points and, in the process, greatly expand the portions of our two campuses covered by the WLAN.Two campuses, currently with one T1 between them (soon to be two), all part ...
When i use config templates in the wlse the job always fails stating that the following command resulted in errors "no dot11 ssid tsunami". I'm running 2.13 on the wlse and this command was not in the template, it is just performed at the of the temp...
I have an setup that I am having trouble with and was hoping someone had an idea. I have a site on IP tel with a remote building connected over a wireless bridge. On the remote side the phone is plugged directly in to the ethernet port of the bridge....
Is there any way (debug, trap,...) the AP can send/show if the external antenna is broken or disconnected? We have lots of AP's installed in a place where sometimes the external antennas can be broken, and I'd like to know if there is a way to know i...
Hi y'all,I just finished a project that consists of Aironet 1310's and some switches. The whole thing is working fine. See attachment for the simple diagram.Next week, we'll be in the commissioning phase and I would like to know what sort of paramete...
I am currently working on setting up a AIR-AP1231G-A-K9 running 12.3(8)JA. I have it configured for EAP-FAST using its local RADIUS server. Everything works perfectly with the Cisco card and client utility. As soon as I try and connect with a Broadco...
Hellohow is it possbile that the configured channel on the ap show when i do the cmd "dot11 carrier busy" 100 busy load? When I change the channel, then the new channel shows 100 busys load.Are this interferences or disturbing noise from neighbors?An...
I have around 15 Sites with individual WDS AP's that show up int the WLSE as KeysSetUpWithWDS. However, I have around 10 sites that the WLSE to WDS Authentication Status shows Unauthenticated. Is there a certain amount of WDS AP's that the WLSE can h...
How much of the performance drops when ap`s are used to do rogue containment? Can I set in the controller that if they find a rogue ap that this by default is set to containment instead of allert?
Hello everybody I`ll like to put 2 AP 1231G in a repeater mode... I just have 1 Root AP and I want to put 2 more AP in a repeater mode. The question is if i could put another repeater from another repeater (non root) that is:(((AP ROOT)))(((REPEATER)...
I installed 2 bridges 1300 as a backup link. This link carry 5 vlans. Everything works except the spanning-tree. As soon as i establish the radio connection, i get a network loop for these vlans. The ports are in forward state from both switches on e...
I'm trying to configure a WLAN composed of AP1242's managed by a WLSE and authenticating via an ACS Appliance. At present I'm still testing so the ACS box is using it's internal user database and I've generated a self signed and installed cert on it....
Hello, My problem ... whith a ACS v3.3, i want connect tot a externel database users LDAP(openldap). I configure externals users database - database configurationI configure externals users database - database groups mapping (it's ok, the link with m...
