Wireless

I was trying to implement a pix to pix lan to lan tunnel over the weekend. I found traffic in one direction was encrypting/decrypting ok. But the reply packets were not getting encrypted. Hoping to avoid labbing this out by asking a question here. Do...

Can the Aironet 1400 be used as a repeater between 2 non-LOS locations also using 1400s. They are only 2 miles apart but can't see each other but each site can see the water tower where the repeater will go. I haven't been able to find any specific i...

Everything worked fine, but afer a power failure all the equipment rebooted (3560, 1100, acs, wlsm). No 7920 fails to authenticate using leap (cckm+tkip). All configs look ok (all of the had been saved) PEAP clients and wep client authenticate withou...

After upgrading to 12.3(4)JA1 AP is unable to register with WDS. Downgrade back to 12.3(2) solves the problem.Did anybody experience this problem?

Hi NetPro,I'm facing some problem with the Cisco Aironet 1200 Series Access Point, Which is the DHCP assigned IP Address to this AP, i've configured static ip to this AP, but when in the Association panel , i saw AP has another IP address as well . i...

My WLAN adapter is MPI-350 miniPCI, and the adapter utility is ACU 6.3.011.I want to find all broadcasted SSID, the useful function which containted in many WLAN adapter. But I can only set the exact SSID in profile manager of ACU.how to scan all bro...

Hi All,I just want prepare the Cisco Wireless LAN Support Specialist Exam: 642-582 WLANFE. Please advice a good book for me to prepare for this exam.Thanks,Srikanth

Hi, the root bridge of our Aironet 1310 bridge, S/W ver 12.3(4)JA, always seems to lose it's configuration for the "distance settings" when it reassociates with the non-root bridge. Current settings are set for 4 km but after it reassociates, the dis...

Can someone tell me how I can bridge multiple access points with the same SSID? I have 5000sqft of space that I need to install. Will multiple Cisco 1100 be sufficient or I need to move up to higher end products.Thanks.

Here is my scenario. I have a Cisco Cat3550 switch. Three of the ports are set to access mode for vlan 2. My WLSE Express is plugged into one, my 1210 AP is plugged into another, and my laptop is plugged into the third. The switch is my DHCP server.W...

I have setup WPA2 and I can logon to the domain but Windows XP SP2 still askes for user authentication.Even though I am using windows to pass the user name and password. i.e. The "Network Connections", "Wireless Properties", "Authentication", “Protec...

Using Aironet Client utility v6.5 with a 350 Mini PCI card on my IBM Laptop.Trying to connect to my home WiFi that is setup to use WPA - on my other PCs at home I specify a WPA phrase / key when I configure the connection.BUT there seems to be no way...

Hello Everyone -I have a WLSE and 2 floors of AP1200's (4AP's) on each floor.The original WLSE Setup & config that was pushed to the AP's was bad, incorrect and even temporarily hosed the network.Is there a tool in the WLSE that will just re-set the ...

Hi,my wireless infrastructure is currently still based on LEAP and WEP, therefore I am in the process of migrating towards PEAP and WPA.During the testing in the lab I have encountered some problems with the client side when i use the Intel Centrino ...

I am in the process of converting my AP1200s from VxWorks to IOS. I have converted a test unit and I cannot find 2 features that were present in VxWorks (web): Distribute Configuration to Other Access Points and Distribute Firmware to Other Access Po...