Wireless

Hiya,After setting up a test bridge link using 2 x 1300 ( next to each other) I managed to get 25mbs through the links using iperf. Though when i put these 2 in place in both buildings was getting 4mbs These were shipped with 8db antennaes made by cu...

I have recently bought a 6210 wireless headset as the it is suppose to be compatible to use with mobile phones and IP phones. I am having a lot of trouble setting one up on a cisco 7960 & 7912. Does anyone know if this wireless headset will work with...

Hello,Ican't enter the bootrom as described by cisco(http://cisco.com/en/US/products/hw/wireless/ps430/products_configuration_guide_chapter09186a00804e7d5c.html)any ideas? HW:1231g-e-k9 SW:12.3(7)BootLoader:12.2(8)JA.Thanks

My customer wants to run the AZR in the SSG router itself. Is it possible ?Anyone running a system with AZRs to give me more design details ?The auth used is EAP-SIM.Tks

Hi everyone,I have a client that wants to use the spectralink phones which requires us to deploy wireless throughout his house. It's a very large home, with three floors and he would like to be able to walk from anywhere without dropping the call. Al...

I have set up a 1200 (image c1200-k9w7-tar.123-7.JA) with multiple SSIDs, one of which is intended to be completely open; dot11 ssid bfopen vlan 69 authentication open guest-mode ! This works perfectly for most clients (Windows, Linux) but a HP IPAQ ...

Hello, everyone! We have setup a bridge connection (root/non root) using 2 AIR-BR1310G-E-K9-R with 12.3(4)JA. Initially the link strentgh was around -50dBm. A couple of days later the link strentgh failed to -70dBm! Initially we thought that the prob...

Hello, I need to backup wireless link between two wireless bridges with ISDN backup.Scheme of network is as followed:LAN--ROUTER1--BR1310 ... AIR ... BR1310--ROUTER2--LAN , the problem is, that all the devices are in the same network, so the router i...

we have one wireless bridging Point to Multipoint links with Cisco 350 series bridges and cisco 350 work group bridges. in work group bridge sometimes going to factory defaults automatically.UPS power is given to work group bridge. no power failuer b...

Is Cisco coming up with DOS and Win CE drivers for the Cisco® Aironet® 802.11a/b/g Wireless CardBus Adapters. This is becoming a big issue in retail stores. 90% of our customers running Cisco APs in their stores and now there is no driver for the equ...

You may be able to help me or direct me to the right direction this is the problem. I am trying to get ready to take the exam 642-577 Wireless LAN design specialist. I could not find a single book that address the Cisco objective exams for the this t...

Hi alli have 4 1300AP/BR i want to connect my branch office which is 3 km away.i have 4 1300 equipments with 12 dBi antenna 2 no's and 13.5 dBi antenna 2 no's.is it possible to put 2 1300 at H.O and 2 at Branch .and one will give you 54 mbps , so if ...

I have a AP1200. AP1200 come with 2 RP-TNC connectors. One is "Right/Primary" and the other is "Left". I want to know which one is Tx or Rx. Can I install two directional antenna that one point to left and other point to right, in order to increase t...

Hi I need your help on Cisco Aironet 1100 WLAN solutions. Design: I'm trying to implement WLAN on outside Firewall (Public network). LAN -> Switch -> Firewall -> outside FW switch -> Internet router -> outside world. I want to connect Cisco Aironet 1...

Need help with bridge configuration. Using two 1300s as root and wgb. WGB has 1200 attached to accept wireless clients. In current setup, clients authenticate, but do not get IP address. Should the WGB be configured as non-root? Can someone direct me...