Wireless

I have a SSID setup with a 128-bit WEP key with a Cisco 1200 AP and a Symbol LA-4123 802.11b card (don't ask why). When I remove the 128-bit WEP key, I can connect to the network, but when I apply the key, no connection.With Symbol being such a big ...

I have a network with some Cisco 1200 Series AP´s. This ap´s have 802.11G radios. When I configure a new template, in the last pass (SAVE) I receivedthis message:Error processing template configurations. No valid device versions supported. This is th...

Hi there,I'm trying to synchronize my Cisco Access Points (AIR-AP1232AG-E-K9) Clock with our time server (win2k SP2).In the Web interface of the AP I can only enter an IP address an switch to "enable" but he is not synchronizing. I only get the follo...

Hi there,What we have now is 2 offices (A and B) 150 meters apart."A" has the server farm and the main WAN link. I just want to extend the lan of A to B (using 2 Aironet 1310 bridges which I already have), in a way so users in B can reach A (servers ...

HiI want to create a wireless bridge between two rooms in the same building. Can I do this with two Aironet 1131AG access points?Any useful information would be much appreciated.

Hello all,I have an aironet 350 series wireless card for my compaq iPAQ H3970. It is setup to use a server-assigned IP address but is having problems doing so.I have looked up troubleshooting documentation for this and a software reset of the device ...

Does anyone know any means to perform traffic recognizion/marking/classification for LWAPP traffic on per packet basis? Is it even possible? I'd like to recognize voice traffic from inside LWAPP and give priority treatment for it...

For the most part, I have been installing the Linksys residential access points in my business. These are not doing the job in a recent install at a hotel/condo. I was wondering what Cisco access point would be appropriate. I can put a couple per ...

I have a WLSE Express that am am using as a radius server for my Spectralink IP phones. I also have WDS and FSR setup and running. The problem is that the WLSE will not authenticate the phones. The radius server log shows the phone coming in and gett...

Hello all,I am trying to implement WDS w/o WLSE. I simply want to be able to be to have an AP in scanner mode report detected SSID's to the WDS device. I have a few questions about this:1. How does the scanner-mode AP report this information? (SNMP...

I have my access-points AIR-AP1231G-E-K9 with IOS 12.3(2)JA2 configured in wpa mode.I have a notebook xp SP2 with cisco AIR-CB21AG-E-K9 card.The PEAP authentication is managed by windows and works on a cisco ACS version 3.3.The problem is that if i e...

Hi, I'm having trouble connecting my Dell Axim X50v to my new 1130 AP. I have a laptop and PC with wireless G cards connecting and accessing the network fine but am having no luck with the PDA.It can see the AP fine and tries to connect but it seems ...

Hi,I have an AP1231 I firstly configure this AP with a single SSID with wpa encryptions and also configure it to act as a local DHCP server. This all worked fine, with clients picking up and ip address etc.Now I need to configure 2 SSIDs, each with a...

I have setup a AireSpace 2006 with 3 AP's for wireless Internet Access at my site. Our SEcurity Folks want to be able to look at the GUI as a IDS. I have found that the 2006 has IDS signatures but I cannot find what I need to configure to make the de...

Even though WLSE 2.11 does not support the new IOS 12.3(7)JA, I tried upgrading an AP to 12.3(7)JA using a WLSE upgrade job and it worked just fine. I ran the same job on about 10 APs, one AP at a time, and it worked every time. What is the max num...