Wireless

Hi,I am having a little issue of the Linksys wireless printe server associating with my AP1231. I have 2 vlans on my AP one using WPA and the other open for printing. My wireless print network will have static ip address, I have local dhcp server on ...

We have identified a security issue with our wireless network that i'm trying to plug. I'm sure that the facility tor implementing this exists but I can find no mention of it within the WAP device documentation, probably because I'm not using the rig...

I am wanting to upgrade my WLSE from 2.7 to 2.9 but I can't find the software anywhere. If I goto the Cisco download page is says none are available. I have a userid and a maint contract on my WLSE. Can someone tell me how to get the software please?...

Can someone tell me if there is a way to establish communications between a 350 and a 1400 bridge. I know the 350 runs at 2.4GHz and the 1400 runs at 5.4GHz, but I am wondering if there is a way to step the frequency down in the 1400 in order for the...

I've been fighting this for 2 weeks now, anyone tried this and has been successful? Where is the documentation to set this up? I've tried numerous supplicants, user settings, encryption methods (WPA and TKIP, TKIP + 40WEP, etc) I had my LDAP admin lo...

When I try to run a CDP discover the WLSE does not see my AP's. If I type a static IP for the WLSE to find it does.I am running WLSE 2.7 and have HP 4000 switches. Any suggestions would be appreciated.Thank You.

Hi! I am new to wireless things and maybey someone can help me with my problem. I have two 1130AG Accesspoints. I have set up one with WPA-PSK and that one works just fine after some configuration. However I have now purchased another one to be able ...

Hi,I have a wireless link from an elementary school to me. The link consists of my Cisco BR500E V8.80 (340) as the root bridge. The school site has 2 buildings with Cisco 340 and 2 buildings with Cisco 350 bridges. I have WEP enabled. The links have ...

HiI need to know what cisco device(s) currently support 54Mgb with distance coverage of 15km?. I would apritiate it if you could also tell me what antena series (if requered) is also needed.Thanks

HiWe're using AP1200's with PEAP-GTC and a Radius server running ACS v3.1 with a RSA Ace Securid server for authentication. The problem that we have is that the passcode failures aren't passed back to the wireless client for the Dell TrueMobile 1450 ...

Hi there.I have an installation which consists in a Cisco Access Point 1100 and a freeradius server connected to a LDAP server.I want to setup several VLANs and assing them to the users depending on what group they belong to. All the freeradius and L...

Our current method of configuring switches is via a TFTP server. In DHCP we give the MAC of the switch a Manual DHCP IP, this causes the switch to pull its name as its initial boot name. When the switch boots it looks for its name-confg. This piece w...

We are looking at using SSG/SESM to deploy WLAN Hotspot networks to our clients. I would like to ask the following from anyone interested in a reply:1.) How difficult is it to deploy - what is the typical time spent (I know that's open ended based on...

Just attempted to upgrade a 1100 from 123-4 to 123-7. Boot fails (three green solid LEDs for 1-2 mins and then a red status. Unit reboots, over and over). Tried to load it via TFTP with the same result. Reverted back to 123-4 and all is well.Anyone e...

I know this has been kicked around on this forum before, but I am trying to look deeper into the issue with the 2200B/G card.I work as a wireless consultant for a company which performs many wireless installations, both Aironet and Airespace in Hospi...