Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, please your help I have a question:When we talk about Active Gain we are talking about a signal booster.Do the cisco antennas have this integrated?For example the Aironet 2800 or Catalyst 9000 series? Because in the WLC you can manage the power o...
Hi I am having a problem getting the APs to join 1 a controller. We have 2 WLCs and the APs are configured to have HA and when some APs must migrate to one of the WLCs this will generate an error.Even some APs we had to remove the HA because all the ...
Hi,Why do clients choose 2,4 ove 5Ghz ? AP is 2802 (56,52)* 40MHz All these devices support Wi-Fi 802.11 a/b/g/n/ac
Hello we have c9800 wlc with ssid corp/byod. Users ahthentication/authrozaiton is going to ise. now we need to create a new ssid. After psk is configured for the new ssid, we input user's mac address in ISE. Question is where to associate the mac add...
Resolved! 9800-40 adding vlan spontaneous reboots
Hi,I have a pair of 9800-40s running 17.6.4 code in HA SSO Active/Standby Failover VSS With Split Links RMI+RP When I add a VLan to the trunk to the VSS core from the 9800 side, the primary spontaneously reboots.Was not the behavior I expected. Anyon...
I am looking into enabling PMF on a dot1x WLAN, on a 9800 running v17.3.5bIs dot1x SHA2 mandatory for PMF to work or does PMF work with dot1x SHA1? Found this guide that says SHA2 has to be enabled for PMF to be mandatory, but on the WLC I can set PM...
Hi there,I deployed vWLC version 7-3-101-0 on ESXI 5.5: When I put the ESXI (vWLC) and the AP on the same network the vWLC did not display AP See the Message Logs from vWLC:*spamApTask6: Jan 01 01:39:32.302: #DTLS-3-HANDSHAKE_FAILURE: openssl_dtl...
I have a controller 9800 (firmware 17.3..5) with more than 200 points, and there was a need for a few more points, I bought it - C9117AXI-EWC-E V01 with a controller (configured as a point). When you connect them to the controller, they work normally...
I work at a metro hospital with about 2000 cisco APs and a high-density design with Apple iPhones providing voice to our staff. Cisco had us use RRM to set all APs to 40MHZ for better data rates, but i continue to get a LOT of tickets regarding dropp...
Good day-WLC 5520 is currently (LAG) multihomed to a pair of VSS Catalyst 6807 switches via a port channel. We are migrating off the 6807 to a VxLAN EVPN overlay on a pair of standalone Catalyst 9606 switches both connected via a Layer 3 /30 link. ...
Cisco 8821 phones will associate to AP's but will not get an IP address. Using the wireless lan profile in CUCM the phone pull the PSK and appears to associate to AP's, but after that nothing further. While attached to docking station and utilizing...
I have set up two WLANs using four 9115AX AP's. I have a Staff WLAN which is accessed via a PSK, on the second WLAN I want to restrict access to the LAN and other clients on the LAN and just gives access to outbound traffic, so people on this WLAN ca...
Hi Some time ago, I had FlashAir Wifi SD Card connecting to wifi without any issues... Now, running with an AP1142, the WiFi SD card connects for approx 10 seconds (the is the time I get ping reply from it), and then the connection is dropped again....
Hi I have a brand new AIR-AP2802I-A-K9 access point . I need to convert this to autonomous. can you let me know the procedure.I donot see the autonomous image in the software download page.
Hi guys,I'm trying to configure a new Self managed AP.The problem is that it need a license and the only way to provision it is to use the cisco smart account.When I try to create an account it tell me that I need a valid company name to proceed but ...
