Resolved! WLC 3504 Upgrade
My WLC3504 still running using version 8.5.140 and i check the latest version is version 8.10.196.0 Can I upgrade my 3504 to 8.10.196 directly or i must upgrade to other version first?
Forum Posts
Hi, I have one query or need guidance. Need to create a ssid with 802.1x in Meraki using ISE as authentication server. I am quite new to ISE. I know I need to add the APs in the ISE. What about the policy? Do I need to create policies also there for ...
Hi,I am using WLAN poller to collect data from access points. It is working for all the access points except C9136 access points.It gives error like this.============================================================Summary=============================...
Dear Community,RE: Integrating Cisco AIR-AP3802I-B-K9 with Existing Meraki NetworkI currently have several Cisco Aironet AIR-AP3802I-B-K9 access points from a previous network deployment. We have since migrated to a fully Meraki-based environment.I w...
Hello, I performed several wired packet captures to compare the behavior between an Android phone and an iPhone on the Meraki MR44 network. We can see that gratuitous ARP requests are correctly relayed by the access point to advertise the Android dev...
Here are few simple lessons learned along the way deploying 6Ghz for outdoor in an IOS-XE controller-based environment, hope it helps someone else trying to do the same, if you learned anything additional, feel free to comment. Also, before using som...
I’m evaluating Meraki for a wireless deployment and wanted to understand from a practical standpoint — what are the top 2–3 workflows customers genuinely find most useful day-to-day?In particular, which workflows actually simplify operations at scale...
Resolved! C9120AXI-B not getting DHCP
I have several wireless access points that cannot get DHCP. I get the following logs:[*02/12/2023 00:53:42.8860] wired0 (Ext switch port: 7) (Logical Port: 15) (phyId: 1f) Link DOWN.[*02/12/2023 00:53:42.8860] ===> Activate Deep Green Mode[*02/12/202...
we have two Cisco Access Points. One has successfully joined the controller, but the other is not joining. Both access points are connected to switch ports with the same configuration. we have also factory reset the AP, but it is still not joining th...
Resolved! 9800L SSID w/ Multiple Profiles & AVC
9800L HA Pair running 17.15.4dSeveral years ago we migrated from 5508 / 2504s at all our sites to this 9800L HA Pair that is in our HQ datacenter. We did have Professional Services assist in the initial setup of the 9800L and migrate the settings fr...
Hello Expert,When i add the C9136I-ROW(17.9.5) device to the WLC 17.12.3.31 image download fail due to WLC rejected image download from the ap log.But WLC site can see the log "AP Model not supported for Predownload: C9136I-ROW".Did anyone know why t...
I need to order several Cisco C9120AXE models with antenna model AIR-ANT2544V4M-RS. I am planning to make these APs join the WLC of model 5520 which is already operational in my network. In the AIR-ANT2544V4M-RS datasheet, i see the below note, "The ...
Resolved! Catalyst 9800 on Hyper v issue
Hello,Strange issue with Catalyst 9800 hosted on Hyper v:Interfaces doesn't work in switch port mode:if interfaces are configured in switchport mode (access or trunk) it seem there is no transmission to the outside.In routing mode it works correctly....
Resolved! wireless 802.11r logic
Hello Community, I would like to understand the 802.11r authentication process in more detail. As far as I know, when 802.11r is enabled, the first authentication is performed normally, and during roaming the EAP authentication is skipped. However, I...
Hi! I've been managing cisco AireOS(ME, non ME) setups for several years and I never had to restrict access to the management webui or cli until now. I've done some searches on the internet and cisco docs and found the cpu acl feature. Using an 1815i...
