Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I need to disable SNMP on our complement of 350 APs. However, I've tried the normal route of disabling via the SNMP parameter (web) page but if I go back to the APs a day later somehow SNMP has re-enabled itself. I've tried turning off CDP to help th...

pwhiteley by • Community Member
  • 852 Views
  • 2 replies
  • 0 Helpful votes

Reading the setup specifications I see that the distance setting should be 99 when in Install Automatic Mode and should return to 0 when changed to ROOT. When looking through my settings the distance setting is 2 km. Does this cause nay problems for ...

jimallan by • Community Member
  • 719 Views
  • 1 replies
  • 0 Helpful votes

Hi.Im having some trouble using the aironet 350.The thing is that i can connect to the internet, but some times i lose the connection. I like using instant messaging, but with this problem is impossible, cause it signs out all the time.Im using the h...

Hi,I have a very strange problem with the radio channels of my radio B interface on ap1200.we are starting our Wireless Service in our library. We are running PEAP. Everyone, can log in fine.But when I do the carrier busy test, it shows that channel ...

k.mahmood by • Level 1
  • 765 Views
  • 3 replies
  • 0 Helpful votes

1210 b and g radios ver 12.2(15)XR2WLSE 1105 ver 2.7.1I've been testing the use of scanning-only AP's and I have a couple of problems that level one support has been unable to assist with. First is that the documentation implies that you can set up a...

anperry by • Community Member
  • 901 Views
  • 3 replies
  • 0 Helpful votes

i have two 1200 ap's, one as root, the second as a non-root repeater ap for testing purposes. they work well but they do not roam that way i expected. i found out that the client changes the active ap when the signal strength is getting very bad, not...

ubach by • Community Member
  • 712 Views
  • 2 replies
  • 0 Helpful votes

Hi,Can you suggest a system based user authentication using any EAP on Linux where the least configuration need to be done at wireless users, Windows and Linux.Thank you.Regards,Delon

c.ong by • Level 3
  • 337 Views
  • 0 replies
  • 0 Helpful votes

Hi,I have a customer who has at least 100 branches nationwide. I would like to propose each branch to have at least 1 unit of AP for a start. However I have a few questions regardign the security aspect of this design, I hope that you can give me a f...

c.ong by • Level 3
  • 371 Views
  • 0 replies
  • 0 Helpful votes

HiCustomer has an original AP 1220b running 11.5(4)T image. He wants to know if he can run 802.11G. I searched Cisco and see that we can upgrade from vxworks to IOS 12.2.13(JA4) using the convert tool but can the 802.11G card be installed in the 1220...

cospencer by • Community Member
  • 766 Views
  • 2 replies
  • 0 Helpful votes

We are having trouble getting our 1310 bridges to work as repeaters. They work great as root access points but not as repeaters. Also what access points are IPV6 capable.

rnelson23 by • Community Member
  • 525 Views
  • 1 replies
  • 0 Helpful votes

Hello,I have a network composed of AP1200 working in the 802.11g band. When I try to see the theorical coverage of each of them with the Coverage Display option, with the 802.11g filter I can't see anything, but with the 802.11a I see the coverage. H...

Is there a way within the ACS system to only replicate certain groups? We have mutiple sites, each with their own ACS servers. I am trying to setup a group on the servers local to me that has access to network hardware, and replicate this group out t...

jogreco by • Community Member
  • 440 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card