Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

We have an Aironet 1200 Access Point at our office. I have experienced a lot of problems installing adapters on laptops. After installing the software and configuring the SSID and WEP, the adapter will show that it's associated; the Access Point also...

admin_2 by • Level 7
  • 710 Views
  • 1 replies
  • 0 Helpful votes

The 802.11 standard specifies use of PS-Poll frames for use in Power Save mode. The Cisco 802.11b and 802.11a cards operate exactly according to the standard, which is good. Once they enter Power Save mode, they stay in Power Save mode, but look at t...

ccie by • Level 1
  • 4033 Views
  • 1 replies
  • 0 Helpful votes

We are about to deploy a 'guest' ssid. The scenario we are struggling with is when a employee connectes to the LAN and the laptop automatically connects to the 'guest' WLAN (dual homed PC with default gateway on LAN). We are trying to figure out how ...

rcreamer by • Visitor
  • 648 Views
  • 1 replies
  • 0 Helpful votes

I have a wireless network with AP 1200 and Clients computers with 350 Series PCMCI Wireless LAN Adaptors and everything is working fine, now I have added a new building with CISCO AP 1300 with the same SSID and the same WEP some laptops wiht another ...

sanchez.l by • Community Member
  • 569 Views
  • 1 replies
  • 0 Helpful votes

Hi. Does anyone know the the meaning of the following error message on Funk Radius server: EAP-PEAP authentication failed - client issued alert 'client closed the session before handshake was completed' We use PEAP to authenticate Windows XP client w...

felix by • Community Member
  • 1473 Views
  • 1 replies
  • 0 Helpful votes

When using a Sup720/WLSM combination with APs, is it possible to mix SSIDs using mGRE tunnels (mobility groups) and local VLANs/SSIDs? Or, do all wireless networks (SSIDs) need to be configured as mobility groups on an AP enabled for mobility groups?

Hi,As I understand the signal strength of the AP's rabbit ears work in a figure 8 pattern emanating outward from the AP itself. If I use the longer range omni-directional antennae 2400MHZ (manufactured by Cushcraft) I believe the signal strength then...

mnewman by • Community Member
  • 1090 Views
  • 2 replies
  • 0 Helpful votes

i am looking at deploying the following:Access points: Cisco 1200'sClient adapters: Aironet a/b/gAAA server: Cisco ACSAuthentication: LEAP (then EAP-FAST when out)Encryption: WPA TKIP (is MIC included in TKIP?)Management: WLSEAll access points will b...

rwcrowe by • Level 5
  • 1064 Views
  • 3 replies
  • 0 Helpful votes

I need some help here please.After the router accepts 10 clients, it just stops handing out IPs. I get the default windows IP for any machine after the 10th connected.Any ideas on what I should look for?thanks.

steveb_coda by • Community Member
  • 644 Views
  • 1 replies
  • 0 Helpful votes

hi i am trying to setup our firm wireless network by configuring the 10 AP 1200 series we have to act like dhcp relay.does anyone know how i can do that?one's of my AP 1200 configuration file looks like : ip dhcp smart-relayip dhcp relay information ...

dtongue by • Community Member
  • 7196 Views
  • 13 replies
  • 0 Helpful votes

Hi,I have a AP1100 and a repeater AP1100. The AP acts as a Radius server and the clients (all AIR-350) use LEAP, WPA and TKIP. Everything works just fine.Now I want to secure my environment a bid more and make use of EAP-Fast. I can't get it work. At...

avanuden1 by • Community Member
  • 1230 Views
  • 4 replies
  • 0 Helpful votes

I would like to enhance the connectivity of our mobiles (now via GSM), allowing also a GPRS connection. The existing GSM infrastructure (3 NAS working with Radius/Oracle) should be retained as a backup in the case of GPRS network problems. Our teleco...

sisal by • Level 2
  • 982 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card