Wireless

I am upgrading some Cisco 1200 802.11g APs from (15)JA to (15)XR1 IOS versions. The config has multiple SSID/VLANs. With the new (15)XR1, WLAN clients are able to associate to the AP fine (back to CiscoACS) but they do not get an IP address. I duplic...

hi folks, I am about to set up a wireless network for our library users that come in from the public and bring their own laptops. We would like to have two options:1) they can open their laptop and just jump on without any authentication. but this tr...

WLSE type: 1105, version 2.7Aironet 1100 devices (267 pieces), IOS 12.2(13)JA4After the upgrade from version 2.6 to 2.7 we have a problem with the WLSE. Device discoveries and inventories run without a problem, but whenever a device goes down the WLS...

Here's what we used to have on most of our computers...Aironet Client Utility Version 3.61 or higherPCMCIA 350 Series Aironet CardsNovell Client 4.83 SP1 or higherWhen the computer boots up and before the Novell login comes up the LEAP authentication...

We recently install two wireless sites using the following:root bridge siteCisco 350 Series Bridge 12.00TOmni-directional mast mount antenna – AIR-ANT 24120non root bridge siteCisco 350 Series Bridge 12.00TDirectional mast mount yagi antenna – AIR-AN...

Since the phones support LEAP, does that mean that the phone supports FSR when LEAP is enabled?Thanks,Dan

Hi,We are implementing WPA supplicant support on a network device(with a wireless client adapter for 802.11b). The network device already supports EAP-TTLS and LEAP support. We can very well do the WPA with EAP-TTLS however we are not sure how to use...

Hi,Can some one guide me for how we can configure NATing on a Access Point ?Thank YouManeesh

Anyone else getting the Cisco-equivalent of a BSOD on Aironet 1231g access points running IOS 12.2(15)JA? It seems to occur when I first fire up the access point plugged into a trunked port - I have 3 vlans defined on my access point. Here are a coup...

We recently purchased a Aironet 1200 and upon bootup I noticed a red display light. I consoled into the AP and saw this boot up message:IAPP: get_ap_dot11_bss_hwidb errorThe Ethernet interface comes up fine and I able to access the web interface as w...

Currently we use both power injector and inline power to provide power to our aps. What is the difference between inline power and power injector?Do they transmit the power in the same way ?Now suppose, the inline power module cannot provide enough p...

According to Cisco AP1200 user's guide, it says for the Parent - Repeater to work properly, we have to enable the Aironet Extensions on both Parent and Repeater.But, Parent/Repeater works for me without enabling Aironet Extensions on the Parent.Am I ...

We input MAC addresses one or multiple at one time, then distribute to 10 APs and works fine. Then we try to remove one MAC and distribute to all APs and it does not distribute to all, only removes from that one AP.Ernie/CA.

I currently have APs (AIR-AP1231G-A-K9) that I am running WPA/TKIP with. I understand that WPA2 and 80211i are next in line for security standards. In order to support WPA2 and 80211i with AES what willI need to do to these APs. Will it only be a sof...

HiSo I've got eap-tls working with W2k IAS/Certificate Services and an AP1100. My clients are all XP/2000 notebooks and each machine has a computer certificate. The problem is that the notebooks are generic (not user specific) and the notebook that u...