Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I've noticed yesterday that my MR52 access pt., that link aggregation is not working. Is there anything need to configure in the Access Point itself? It was working before when i installed it., speed operation should be a total of 2gbps for both 2 x ...
Resolved! Retrieve RF Basic Profiles via API
I need to document a lot of networks before a template migration.How do I find the Basic indoor and outdoor rf profile via API?RegardsThomas
Hi Everyone,Kinda new to this community, I want to share and ask for help to solve a very strange case in our office.In our three-story building, 2nd floor works fine, however 3 out of 11 MR 56s on the first floor report DHCP failures, same as our th...
What is the license type that should be pushed on the MR to connect it to MX in another branch?
Hello Professionals,From 2 days ago, my wireless controller (WLC9800-L) freezing suddenly.- version: 17.9.3This device is directly connected to C9300L switch port with Trunk - Trunk(with allowed port).I was accessing Web GUI of controller, but sudden...
Hi,We would like to build a small WLAN network. Therefore, we would like to purchase one WLAN controller and (at least) two access points. We need the WLAN network to support at least:-Wi-Fi6E 802.11ax-Fast Initial Link Setup (FILS) 802.11ai-Fast Tra...
Hi,I have a Cisco AIR 1131 access point(firmware is c1130-rcvk9w8-tar.124-10b.JA3), when i type cli command : sh ip int brthe following syntax appears : FastEthernet0/0 is up, line protocol is down! Please help me fix this error.Thanks in advance.
HI,WE HAVE A CISCO WAP-131 BUT AFTER A POWER FAILURE, THE ACCESS POINT HAS THE POWER LED BLINKING AND DOES´NT WORK, CAN YOU HELP US PLEASE?BEST REGARDS,JUAN M. QUINTANILLA
Hello,About 1 year ago, to expand WiFi coverage, we purchased AP Catalyst C9115AXI-E. As the version of the WLC 5520, in SSO and CAPWAP, did not support the new APs, because of the AIR-CAP1602I-E-K9 series AP, it was decided to make use of the EWC th...
Hi,I have a Cisco AIR 1131 access point(firmware is c1130-rcvk9w8-tar.124-10b.JA3), and when I try to save any configuration, an error message appears: "NVRAM Verification Failed". Please help me fix this error. Thanks in advance.
WLC 3504:8.10.151.0AP C9130AXE-H, External antenna for AXE(enable port A+B): AIR-CAB002-D8-R= + 2*AIR-ANT2524DW-R And AP C9130AXI-H(Enable All ports) From the client side, RSSI is very strong(-20dBm), but the data packets send from Cisco AP is very ...
Hi Guys, I need a help regarding WGB. Before it was connected in WLC8540 (8.5.131.0) with root AP2802. Recently i swapped root AP to catalyst AP9120, also migrated to new WLC8540(8.10.183). But WGB failed to connect to SSID PSK based. Though PSK is ...
Hello Cisco WLAN experts, we are suffering obviously from a CDP/PoE-mismatch problem between Cisco WLAN 3800 APsand small Cisco SG350-office-switches. The result ist that the WLAN AP is drawing 15,4 Watt onlyand all antennas are no longer working. Th...
Resolved! One way SSID for IoT devices? (not VLAN)
Hi everyone. Is it possible to create a one way SSID for IoT devices? Meaning LAN devices can communicate with IoT ones, but not the other way around. That's how I have things currently set up with non Meraki gear (annoying situation to get around bu...
We have an HA failover pair of 8540 WLC controllers. The primary unit in the pair has thrown an error (though it is still functional) and cisco has sent us a replacement unit. I have been unable to find any official procedural documentation for rep...
