Wireless

We just bought a Cisco 1100 Access Point 802.11g and up and running correctly. However, I cannot find any setting in the configuration webpage not to broadcast the SSID. This will make that the normal users do not discover our AP in their auto scanni...

I have 3 1120 APs in a large open conference room with latest 12.2(15)XR IOS. If 25 laptops with wireless cards come into the room, what keeps all of them from associating to a single AP?Is there a tool that will have the APs talk and try and distrib...

All - I currently have a 350 WGB and need to order another one. However, I was told these are now EOL. What can I order in it's place? What I need to do is get wireless from one area to another and then connect an 8-port switch to that wireless devic...

I have spent several hours on the phone with TAC. Make a long story short Some of my 350 AP are missing the Var Installation Key. We have tried upgrading its IOS from 11.06-12.01-12.04 and to VXworks. The upgrading of the image works, but still same ...

I have a VX Works AP1200.. When we connect to it using the Funk Oddsey client, we get the "Hostname" of the AP as the identifier (i.e. what ap we are associated with)..On an IOS based AP1200, we have set all the usual hostnames, etc, however we only ...

It appears that ACU 6.3 doesn’t work with Cisco’s A/B/G card, only the “Aironet Desktop Utility”. Does anyone know if there is a work around? We use a lot of the radio measuring tools (including the site survey) that are in ACU.Thx!

Anyone running 7920's on non-Cisco AP's ? Symbol AP-4131 or Lucent AP-1000 ? Firmware versions ? Caveats ? Mixed data/voice environment ?

All of the users in my company have laptops with Aironet 350 adapters and the Client Utility installed. I have configured the laptops to "Not allow Windows" to manage the wireless settings.How can we use the Aironet Utility to search for available wi...

Hi buddies,I know that is not a good question, but I've a client very insist about latency information.Anybody know where is possible to find something?Regards,Waldemar

Hi. Interesting problem. Have AP1200 with 12.2(15)JA1 and dual radio (.a and .b). Auth is with a Cisco ACS 3.2(3), Windows Domain, LEAP and one SSID on a single VLAN. I can always associate with both radios, .a and .b, HOWEVER I can never receive an ...

Hello,I want to configure LEAP with ACS on my AP1231. (config-if)#ssid test(config-if-ssid)#authentication network-eap myEAPI configure LEAP on Cisco clients too with 802.1x -> LEAP. When I want to associate and authenticate my client, there is the w...

Looking for a solution that would cover a large area with ok throughput...I understand as I get further out it drops off...thats fine...Just looking for a possible combination that anyone may have used to give a compound a decent hotspot. I am lookin...

We have an AP1200 which looses ethernet connectivity intermittently.The particular AP1200 is in repeater mode.As of date we have not ported any Wlan devices on the system, we are just monitoring it using what'sup gold.the primary AP1200 does not indi...

Hi Guys,Just a quick question, if the label behind my AP1200 at the bottom right panel is missing, is there any other way for me to locate the MAC address for the AP?I've managed to hook it up to my office network and am trying to set the IP address ...

Hi!I am planning to upgrade my WLAN security wo WPA and LEAP. I tested LEAP on W2K with ACS and it works fine. About configuring WPA, do I need a supplicant for Win2K and WinXP? Where can I get it?Can someone post a link abount configuration of the A...