Wireless

I'm looking for a good explanation regarding the following:XXXXX Aironet AP 1210 Radio-B Port Dot11Radio0 Packet Error is in Degraded state (29%) P4 Degraded 15:26:59 06/07/2004 I've set up the faults, but haven't came across and good explanation how...

If I configure CCKM, will CCKM dynamically change the session keys or does that still have to be done in the RADIUS server?

If I configure CCKM on my AP, does that trigger 802.11i RSN Information Elements (IEs) to be transmitted with the AP beacons and probe respose frames? If CCKM or WPA is not enabled, I'm assuming that the beacons would look like the original 802.11 st...

When configuring a VLAN using LEAP authentication and the "encryption mode wep mandatory" command, what encryption type is being used - 64(40) bit WEP or 129(104) bit WEP?If you use "encryption mode ciphers tkip", are you using 64-bit or 128-bit WEP?

I have two Cisco WLAN adapters, CB21AG and PI21AG. I would like to setup a 802.11g (2.4Ghz 54Mbps) (in adhoc mode) connection between two computers. However the connection is always established at 11Mbps. (Computers are close ( 3-4 ft), and only the ...

I have 8 1200's connected a local network, they are using a radius server for 802.1x. The client machines are suppose to get a DHCP address from the DHCP server on the same network as the AP's (that have static addresses), so far I have only once bee...

I am running PEAP with Cisco AP 1200. It has happened more than one time that the AP is not responding to new association although there are active assoications in the AP. I have to restart to AP in order for it to work again. Does anybody encounter ...

hi i'm using 1230 B access point and i'd like to set a starting page (home page) if anyone using my wireless network. so if an user start his browser, the first page displayed in the browser should be the one i set, like if you use starbucks wlan,the...

I recently configured WEP between 2 wireless bridges. They seem to be communicating fine, but how can I verify that the WEP encryption is working, like utilizing any Debug commands. Also, if I use 4 WEP keys, how does that impede the performance of t...

What is this config missing to require the client know the WEP key to get on the network? Someone said they could get on my network, are they lying?interface Dot11Radio0 no ip address no ip route-cache ! encryption key 1 size 40bit 7 6C770C504D00 tra...

I have an Aironet 1200 Access Point and a laptop with an Aironet 350 Adapter setup for a site survey. I would like to do a continuous ping while I'm conducting the site survey. The site survey works fine but I can't ping the access point. Does anyone...

Our ORiNOCO (Agere) 802.11b cards, like a Lucent Silver or Dell TrueMobile 1150 mini-PCI cards fails to assoicate with AP with using the Cisco 802.11g upgrade. If I switch the AP back to the old 802.11b mini-PCI card they connect fine. The 802.11g up...

In Europe we can use 13 b/g channels . So suppose we take channels 1,5,9,13 . Each of these channels is then separated by 20(4*5) Mhz . Knowing that each channel is 22Mhz wide theoretically the cochannel interference should be minimal . Has anybody p...

I give. What am I missing when trying to upload a new firmware? I have downloaded the 8.80 upgrade, am attempting it from 8.65.2. The file extensions are .450 and .mib. I cannot find detailed info, even on EOL pages, that descride either how to conve...

The VxWorks verison of the AP1200 had an option to block all interclient communication. Unfortunately I can't find this feature in the IOS version yet...Do you know how to do this in IOS?Thanks in advance!