Wireless

Dear Sir,I have conducted a site survey with the following conditions:-a) AP 1200 with transmit power set to 100mWb) Antenna 12 dBi Omni is used. The antenna is mounted on top of a pole.c) The pole is 11m high and a 50ft cable is used to interconnect...

All,Does anyone have any websites or information regarding Wireless LAN site survey? Follows is what we are trying to do.Several business customers wish to have high-speed internet, and they are more then the 12,000 feet from the Phone Center, so DSL...

Hi guys!I have a project to make a public wireless internet access network. I'm going to use 1200's ap's for access and 350's to make the wireless backbone to connect the ap's to the main site. For the bridges i'm going to use yagis...nothing wrong h...

Dear all,Can anybody tell me what this message means:-"Sender is Leaving (has left) BSS"We are having a lot of trouble with wireless bridge we have set-up (the radio side of the link seems to drop out on a regular basis.I have looked on the Cisco sit...

Hi,I configured a Cisco AP 1200 IOS with PEAP.Hereby the AP Config:aaa new-model!!aaa group server radius rad_eap server 192.168.4.58 auth-port 1645 acct-port 1646!aaa group server radius rad_mac!aaa group server radius rad_acct!aaa group server radi...

Does anyone know if there are any MIBS available for the AP340 ?Also if anyone can give me some guidance to get the MIBS into NMIS I would REALLY appreciate it.------Mike

I have converted 5 350 series APs from VxWorks 12.01T1 to IOS 12.2(13)JA1 and have run in to the following issues:* The enable password is in the generated conversion template (if I look at the file directly) as <END>enable password 0 <ena_passwd>, b...

Here is the question. What is the difference in a AP350 when you set the radio to optimize for range vs. optimized foor throughput? We have a customer that has some "cheap" laptops that will only associate with the AP's if they are set for throughput...

I have access point running on 12.2(13)JA3 and a gateway 450 with an Inter pro/wirelss 2100 and all is fine when using LEAP. Once I change to PEAP and install the certificate it fails to authenticate and the wireless keeps failing/authentication/disa...

Hello!We are bound to deploy a large WLAN at a school here, both for student and employee acess. We have a wired system based on 802.1x and PEAP so we are going to keep PEAP for the WLAN as authentication mechanism. The AP's will probably be 1230 and...

I have a customer with more than 1800 350 series APs running VxWorks. They want/need to upgrade to IOS, so WLSE seemed like a no-brainer. However, they had had a demo unit at some time in the past and wrote it off as garbage. Consequentially, they ar...

Hello, I just installed a Netgear MR814v2 DSL router at a location. They are using a Aironet 4800AP to connect all clients internally. Can this AP bridge or repeat with the Netgear so they can use it at their default gateway? I can't find anything to...

When sending encrypted data, where in the packet is the Transmit Key identified so the recipient can decrypt the packet?

Hello I just added a new PC to a wireless network controlled by a Aironet 340 AP. The AP can see the new PC (with a PI21AG PCI card) but the new PC is not an address via the DHCP server on the router. If I manually add an address to this PC I can pin...

Hello,Today I set up a config with 4 1200ap's and 1 cisco acs for leap authentication and accounting. This works fine.However I would like to finetune this with the result that each user can only be authenticated once. This to prevent several users f...