Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! 9120AXI Line Protocol Up Status Down
Hi,I am having an issue with a 9120AXI and not sure how to fix it. I have it booted up after a config reset and it cannot seem to bring the line up. When I run sh interface brief it shows wired0 status down, Protocol up. I have tried setting an ip vi...
Hi,In our topology we have 2 catalyst switches as stack and a single WLC (9800-L). We need to configure port-channel between these devices. Is it possible to configure between a single WLC and two Stack switches, if it is possible please guide us how...
Which model of cisco AP that can't be converted to lightweight mode?This is to prevent me from puchasing wrong cisco access point.
Resolved! 9120AXI 802.3af POE
We are in the process of replacing some older legacy access points with 9120AXI access points that will only temporarily be connected to switches that only support 802.3af(15.4) poe power. These switches will be replaced with switches that will supp...
Hello Community,Is it possible to configure Cisco CW9166 Access point device as a client? Does this operating mode supported ?I would like to use two CW9166 devices, one acting as an AP and other as a client.Thanks
1. What is the current purpose (A) of C9115AXI-K? 2. Is there a difference between booting the AP and using it normally (assuming resource usage at 50%)? 2-1. If there is a difference, how much is A for each? 3. Can the difference in current consumpt...
Hi , I have a site having mixed of 3802, 2802, 1552H model of APs joining the WLC model 5520 in HA pair. I need to now newly add 9130AXI AP model. Due to IOS compatibility issue, I am making the 1552H model of APs to join a spare 3504 WLC in HA pair...
Hi,I have issues while changing my AIR-2802e-a-k9 into a standalone AP. I used the below command with tftp#ap-type mobility-express tftp://192.168.20.50/AIR-AP2800-K9-ME-8-10-185-0.tarThe new image is downloaded successfully, however I have the follo...
I know little about networks so excuse my ignorance. Our campus has a network with 22 Meraki 42/56/78 APs. I had to move my office's AP into another room to solve a problem there and now my office is the only place without WiFi access. It is a small ...
Greetings,I recently acquired four Cisco Catalyst 9120AXE EWC Access Points for deployment. I began by provisioning power to one of the Access Points using a power injector. Following this, I initiated a factory reset utilizing the power mode setting...
Hello all,I'm hoping someone here can point me in the right direction. I have several AIR 1832I's that come online and seem to be working fine then they reboot. Sometimes they're up for 10mins then reboot, some stay up for 1hr and reboot. The only th...
I have an AP that is stuck at the ap: prompt. I do a dir and it has no IOS currently on the flash. The network admin before me installed the ap and threw away the power adaters because we run poe. I have the AP connected to a powered switch and I als...
Resolved! Cisco 1832i bootloop
Hello.. Anyone have this problem ? I have Cisco 1832i with bootloop problem after try to install ME [04/12/2019 14:59:39.6123] mkp_lg: HW WDT trigger...[04/12/2019 14:59:39.6123][04/12/2019 14:59:39.6123] Kernel panic - not syncing: HW WDT trigger......
Dear Team.Currently i have total of 100Access Points of model mentioned in the subject line, but unfortunately I don't have controller to manage the access points. Please guide how can i make these access points as Mobility controller so that it can ...
Has anyone had issues with clients not connecting to MR66's? I have a couple that the AP is on the network, broadcasting a signal on both bands but no clients will connect. If I reboot the AP the clients connect and the AP will work as expected. This...
