Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I'm new in this technology and don't have any experience in this technology. Can I create VLAN in WLAN equipment if no, what is the options that I have to seperate the LAN? How do I protect a secure site using a WLAN? Hope anyone can help.Thanks
I`ve set up three Bridges in a line, the two on the outside each have a yagi pointing to the middle bridge. The middle bridge has a 2 x yagi`s pointing out in each direction on the two ports. I am getting a bandwidth drop to 1Mb when transporting lot...
Hi. I have a 350 with IOS 12.02T1 and XP is running FW v5.20.17 and NDIS driver v8.3.10. I am not using any network auth just 128bit WEP. When I set up a simple network it works, but if I enable MIC and TKIP I cannot get an IP address! I seem to auth...
Hi !!Many PDAs etc. today cannot accept PCMCIA cards but they do have a slot for a compact flash card (many with support for network cards...).Other vendors supply wireless LAN cards in CF form factor...Are there any plans for such a card from cisco ...
Users reported various Toshiba Tecra 8100, IBM T30s, and a couple of different models of Dell laptops with Windows 2000, SP3. Intermittently, after Windows startup, past LEAP authentication and Windows will crash with stop error: 0x00000000 (0x000000...
Hello, I'm trying to get using snmp who is the root bridge, from a non-root bridge- Although I've found an OID awcDot11TpFdbCurrentBSS - 1.3.6.1.4.1.522.3.12.5.1.15which is supossed to give me the BSS to which the station is currently associated, I g...
Hello!The new Cisco Wireless Bridges 350 Series have 802.1q support. Is it possible to upgrade the old 350 Series Bridges with the last firmware to get this feature on the old 350 Series equipment.Thank you very much,Valery
HiI have the problem with an AP340 (i know this is old ). We use leap and i have the newest sw 12.03t. everythink works fine, but i alsways see the eventlog messages on the HOME screen:2003/06/25 14:57:28 (Warning): RADIUS verification failed for Ser...
Have two 350 series bridges connecting 2 LAN that are about 100 meters apart. The installer used omni antennas. I can connect across the bridge fine when the bridge is NOT connected to the production LAN at the central site. (I have a PC and the brid...
Is it possible to make the AP1200 as a bridge unit? what I can see from the role selection is repeater/non-root option.regards, Sam
I have a Linksys Wireless Router running on 2.4ghz using a DSL Connection. I want to setup an old Cisco Aironet 350 Access Point as either a WIRED Bridge or a Wireless Bridge to boost the signal to my backyard office.I have the Ciscp AP Ver 11.07 con...
I am using Cisco AP352's as AP's on a WISP network. I have customer's buying their own CPE and most talk just find with the 352's. I have one customer that has bought a Smartbridges AirPoint Total. It does not seem to want to associate with the Cisco...
Hi,Can an AP support Cat 6 cabling in future?What is the MTBF for a 1200 Series AP?Thanks.Regards,Delon
Under NETWORK INTERFACES on a AIRONET 1200 I get 'Radio0-not installed' and 'Radio1-not installed'. This is brand new access-point running 12.2(11)JA . I have reset it to factory defaults and reloaded all the firmware. Any help?
Hi,I am relatively new to wireless networking and have a customer site to set up, but I am not sure what equipment I need to make it work properly. Here is the situation:Building A has roadrunner business connection.Building B needs access point to c...
