Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi all,We’re evaluating Meraki Dashboard for mixed environments and I’m trying to understand the scope of Guided RCA. Does Meraki’s Guided Root Cause Analysis work only with Meraki MS switches as mentioned in the screenshot below?If we onboard Cataly...
Hi community,does someone has tested or using a combination of CW9172I + IPv6 + named VLAN + MR 32.1.5 .In my setup I can't get an IPv6 address via DHCP with my SSID configured in bridge mode with using named vlan.If I use the VLAN ID it works well.W...
We are currently testing Cisco ISE for 802.1x wireless authentication.When it uses the default port 1700 on both the ISE and SSID, it fails with an ISE log message of11052 Authentication request dropped due to unsupported port number.I can see in Wir...
Hello, do MR44 APs need to see each other over the LAN management or do they only need Internet access to contact the Meraki cloud?
Resolved! C9800 certificate renewal automation
Hi all,Is there any functions or tips to renew the SSL certificate on WLC C9800 automatically ?Currently I'm importing certificate signed by valid CA(GlobalSign) maunally once the year, to prevent browser warning of WebAuth page using for guest WiFi....
HeyI've been trying to lab a couple of things today, one of them being Wireless Trusted Access. Since Meraki now supports Entra ID integration, it's possible to use Entra and IdP for the Wireless Trusted Access.After working through a combination of ...
We have a couple rooms with exposed truss ceilings. Our old APs have their brackets wire-tied to the bottom of the truss. Does anyone have any better suggestions for mounting the Meraki MR44 to this type of ceiling?
Hi All, Trying to pair two Wireless controllers, direct link on the RP port. Have turned redundancy settings on on both controllers in the GUI. Secondary reboots? getting an ISSU error code 10. The process must of worked somewhere as both are aware ...
*Dec 1 10:04:34.007: DTLS_CLIENT_ERROR: ../capwap/base_capwap/capwap/base_capwap_wtp_dtls.c:509 Certificate verified failed! *Dec 1 10:04:34.007: %DTLS-5-SEND_ALERT: Send FATAL : Bad certificate Alert to 172.17.68.201:5246 *Dec 1 10:04:34.007: %DTLS-...
Hi everyone,We have been dealing with a wireless issue for quite some time now. At first, we believed it only affected a few robots, but during testing yesterday we confirmed the same behaviour on a laptop as well. The problem occurs specifically dur...
Hello There, I'm in a new deployment with an Anchor 9800CL, where the mobility tunnels aren't fully establishing. I'm detecting the following errors on the WLC foreign. 038011: Dec 1 23:25:16.095: %MM_NODE_LOG-4-DTLS_HANDSHAKE_FAIL: Chassis 1 R0/0: ...
Hello Experts i need to provision the 9800 controllers in my customer's network . i have defined all the configuration in dna center , there is an option for anchor groups where we can configure anchor controller IP addresses and priority. currentl...
Resolved! Meraki NAC vs. Access Manager
Hi ,I have a Meraki wireless environment without switches. I want to connect users with a certificate but I don't have a radius server.Can the Meraki NAC / Meraki Access Manager solution help in this case?Which solution is easier and faster to implem...
Hi all,I have an issue on my 9800-CL, when I check : show ap image detailsI can see many Aps with a Corrupted IOX imageSomeone know how can I fix it ?
![2025-12-02 13_05_13-NHKHKGCSRIHWC20 (1) - SecureCRT - [NHKHKGCSRIHWC20 (1)].png](/t5/image/serverpage/image-id/256130i069B8646023B5D5B/image-size/medium?v=v2&px=400)
Does anyone have the above referenced feature working on the 9800s?Essentially a VLAN group of example 4 VLANs, and various users within these VLANS use static IPs or DHCP reserved address and need to go into the correct VLAN without being assigned t...
