Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
The problem with this wireless bridge link is that connection between the two units intermittently lost when any of the end-stations at the remote or local-end start sending data over the link. Both Yagi antennas are installed in an open area (line-o...
We have a small network (10 wireless hosts), all works with Wi-Fi 802.11b and I don't know why, sometimes one or two machines can't see each others, so if I have a shared printer, a machine can't print.Is there a problem of the technology?
I have install 3 bridge 350 CISco wireless. When I chak out the network map it can also detect some other AP and a bridge not in our network. How do I prevent that. I didnt Allow "Broadcast" SSID to Associate which I think will to it but it didnt.Is ...
Hello,I have a customer who has a wlan network (AP 1100) with a standard config (no security) and is asking me how to use his laptop in airport and so on when he travells.As i do not know how configured are the hot spots i need someone to help me to ...
I have to 350 ap's running. One goes into a switch over a trunk port and the other into a second switch over a trunk port. When a client is associated to one AP but then loses association for what ever reason and then associates with the other AP wha...
We are looking to connecting 3 networks together using BR350 bridges in the following configuration. Network A (root) -- Network B (non-root) -- Network C (non-root)During testing we see good throughput from A<->B and A<->C but it is cut in half for ...
I am trying to build a wireless network with fair security but without the users having to go through multiple authentication procedures such as VPN. Also, cost is an important concern. The features I am trying to get are 128 bit WEP with dynamic key...
On this unit, if any single user (worse if more users do the same) performs sustained "heavy" loads (1.5Mbps or higher) the ping times start climbing higher and higher, eventually staying around 700-2000 ms. If either a warm or cold restart is perfor...
Do I have a chance to put my cisco nic 340 into promicious mode. I like to see frames running through the wireless network (managament and data frames).Ethereal and SnifferPro do not show any frames running on top of my nic. Using a smc nic, everythi...
Anyone got the reading materials for this paper? Pls assist....
I have a point-to-point link with 2 350 bridges 10miles apart. I use two directional antennas for the link. The bridges were set to a data rate of 2mbps. The links worked very well for about 6 months. Of recent I started to get signal loss until I ch...
Hi List,I have 5 point-to-point links, 1 using the old 340 series and 4 with the new BR-350. The problem is that when I inject traffic I lost the link and it appear to flap (goes up and goes down) for 1 to 10 seconds. This problem just pop up last we...
I have been testing older client adapters (Cisco Aironet 350 series) with the latest firmware and drivers (windows 2000). I am connecting these to a 1200 Seriel AP (latest firmware installed 12.02). I am noticing that the older cards (about a year ol...
My setup is ACU5.05.01 on Win2K -> AP1200 -> ACS3.1 -> Novell NDSI have installed both Cisco PEAP supplicant and Win2K PEAP supplicant. And I believes that I had overwrite the Win2K PEAP supplicant with Cisco PEAP supplicant as I installed Cisco PEAP...
is this deployment possible [ root(yagi)---- non-root w/c #1(omni)----non-root w/c#2 (omni)].1) all br350s are in a row2) all br350s are same channel.3) the distance between root and non-root is over 500m.4) wireless lan client is only one user, and ...
