Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I am confused, when using Leap does the Wep key get changed each time the client device roams? What kind of time delay does this cause. Does the Access Point give out the new key or do you have to go all the way back to the Radius server to get the n...

dteet by • Community Member
  • 1079 Views
  • 2 replies
  • 0 Helpful votes

The 'SSID1' field gets changed to all vertical-looking bars or boxes when the client associates with the AP. I can change the SSID back to 'johndoe' and it associates, then unassociates. If you go back into the utility, the SSID is changed back to th...

gino by • Community Member
  • 926 Views
  • 1 replies
  • 0 Helpful votes

I have two Aironet 350 APs installed in our Enterprise wharehouse. I keep getting the error message "Network Bridge Loop: Received packet from Self destined to [AWC Mcast All]014096ffffff on port "fec0" on both AP. Is there some extra config that mus...

cmd1 by • Level 1
  • 1278 Views
  • 4 replies
  • 0 Helpful votes

I want "restarting" BR340/350 by SNMP. How do it ?Like ".1.3.6.1.4.1.551.2.2.4.1 i 1" for BR200(Arlan640) ?aleks.

aleks by • Community Member
  • 886 Views
  • 1 replies
  • 0 Helpful votes

We are running a lot of BRI340(11Mbs 1/2 Duplx) wireless bridge links with multihops i.e repeater sites.We use the same unit all the way through.The two units at rptr site is connected with crossover utp >o.5m.Supposed Throughput is 4.5Mbs but testin...

jkymdell by • Community Member
  • 970 Views
  • 1 replies
  • 0 Helpful votes

The 'SSID1' field gets changed to all vertical-looking bars or boxes when the client associates with the AP 350 Access Point. I can change the SSID back to 'johndoe' and it associates for a couple of seconds, then unassociates. If you go back into th...

gino by • Community Member
  • 1289 Views
  • 2 replies
  • 0 Helpful votes

I have implemented a Cisco Wireless LAN with Cisco Aironet 350 Series AP's and Radio Cards. We were concerned about the issues with Static WEP and have implemented a Cisco Secure ACS Radius Server to provide Dynamic WEP (Leap enabled on the Clients)....

RayDMays by • Community Member
  • 2228 Views
  • 5 replies
  • 0 Helpful votes

When an AP is set for all data rates (1,2,5.5,11), does it drop to the lowest common data rate? In other words, if a client is connected at 2Mb, will the AP drop to 2Mb for *all* clients sessions, or can it adjust to multiple data rates for multiple ...

ertrqueen by • Frequent Visitor
  • 1208 Views
  • 1 replies
  • 0 Helpful votes

Other than the standard CISCO AP , NIC and RADIUS server,is there any recommended product (hware or sware) I should be looking at before attempting to put a basic wireless LAN together...First time attempt

Hello, I have a used router that I bought to study for my exams When I console to the router it gives me a password (after the router checkup) which I don't know. How do I get rid of that? Is there anything like "format" on this router? Any help is n...

lordbyronrd by • Community Member
  • 1016 Views
  • 2 replies
  • 0 Helpful votes

I want to connect some Aironet 350 bridges with another one in a centralized location to achieve a wireless communication that let me not to use leased lines or something like that.The distances are large, so I'll use a dish in the satellite location...

dlopez by • Community Member
  • 1043 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card