Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Working on getting local webauth guest access working on a C9800-CL. I have the accounts created. I want to limit which account can log into which WLAN. I've put in the WLAN Profile in each guests account but each user can log into each guest port...
In the controller all of the APs are showing as Repeater mode. I am able to ping the APs so their data is still working properly and internet access at the facility is working still. Any ideas?Edit - If I connect to the web gui of an AP, it shows tha...
Hi All- We are doing some bandwidth testing and I wanted to set my 5520 up on a single 10 Gig connection. The previous config was two 10G trunk ports in a port channel. I configured the switch port as a trunk without the channel group and set "LAG ...
Resolved! MR86 and ANT-27
Can I use two ANT-27 antennas facing 180 degrees apart with a single MR86? Is Meraki Wi-Fi Channel and Power Management effective in this configuration? Does it sense at the antenna vs the base unit?Are there any issue with extending the ANT-27 away ...
In our lab I have deployed a Cisco Spaces 3.1 connector in our lab. Its registered and working and all looks ok on https://dnaspaces.eu. I have added the C9800 WLC and pasted the configuration script that was generated to enable NMSP etc. The conn...
Hi,As the subject states, are there limitations/pitfalls to using Meraki Cloud Authentication to manage SSID access? User credential mgmt. looks forward but curious:Are there limitation on the number of credentials that can be created?There doesn't s...
Hi guys, can anyone help clarify the uses and differences of AP-manager interface and manager interface? From boson exsim the explanation states that manager interface is for L2 communication between WLCs and APs and AP-manager interface is used for ...
Hi,I there any way to control Bandwidth rate dynamically using RADIUS response in "MAC-based access control" mode?I know how to do that via polices, but i need to control it dynamically, per authentication, something similar to that:WISPr-Bandwidth-M...
Hi,Assuming that I have one AP connected to Meraki cloud, with "MAC-based access control (no encryption)" security mode enabled.I also have "RADIUS CoA support" option enabled.What is the destination IP for CoA messages? Is it the same as Meraki cons...
Are the c9120axe-b external antenna weather proof? They don’t seem to have any weatherproofing, the ports are wide open to the elements
Hi,I'm trying to update my AP from the controller via tftp but I get an error while downloading the image.Logs From EWCAug 23 10:45:59.048: %INSTALL-3-OPERATION_ERROR_MESSAGE: Chassis 1 R0/0: install_engine: Failed to install_add package tftp://10.25...
I'm managing a network with 266 of the above WAPs with dual 5520 WLC's. Up until yesterday all WAPs were connected to the controller and everything was humming along nicely. The switch stack that the WLC's connect to had a wobbly and needed to be reb...
Hi CommunityWhat is the command to set both radios to run at 5 GHZ only. Our controller is an 5520 running 8.10.183.0. Most of the AP's is 9120, and they should be capable to run both radios on 5 GHZ.But I can't find the commands nesccsary to do this...
Hello,i am currently preparing the deploment of a C9800-CL for our headquarter and some branch offices.We want to use flex connect for all sites with local switching.In our headquarter we will have all APs on vlan 101Clients are on different vlans 10...
Hello All,I've got a problem with my AP on 2.4GHz.It shows maximum 14dBm max TX power which is less than the specs.Country is Hungary which should allow more TX power.Is there any limit or hint or advice?AP works as ME mode.Many thanks!
