Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! APs Cannot join the Controller
Hi all,My APs can't join the C9800-CL ver 17.6.5. The controller is run on a HyperV server.1) Certificate is configured, and I see it with: sh wireless management trustpoint. 2) I configured the DHCP scope in the controller 3) Checking the DHCP bindi...
Resolved! MR Advanced licenses - Use Cases
Hello,I'd like to know about the scenarios that I get to offer Meraki MR with Umbrella. What sort of environment can I use Umbrella in WLAN?Anybody could help me, please?Thank you,
Hello ExpertsWe got a small setup with 6 standalone AP model 1142. DHCP server is Windows 2003, all were working fine but lately we noticed that AP cannot provide IP address to users, this happens to all AP now. on checking we didnt find any issue w...
I have trying to join my new AIR-AP2802I-D-K9 with the same AIR-AP2802I-D-K9 WLC, but its shows the error massage "Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10)"
Resolved! C9136 XOR Sniffer mode crash
Hi,I am using 17.8.1 (9800CL) with two C9136 APs. I am creating this discussion in hopes to find other people with the same problem. My problem is that the sniffer mode works for a while, but then out of the blue it stops working and you have to rese...
Hello,Has anyone set up MAC authentication with a pre-share key? I only see MAC authentication or Password not a selection for both. Thanks in advanced.Rodney
Hi, We had an issue with APs whose certificates have expired. However, we have upgraded the WLC to the fixed version 8.5.182.7, but I still have the same problem. What could be the solution? When I enable 'config ap cert-expiry-ignore {mic|ssc}', the...
Hi everyone,we have one SSID which is distributed to all access points and uses its own VLAN per building. This means that I distribute a separate tag to the access points per building, so that only a specific VLAN is used at this point. This works s...
Hello, I hope you are well. I have a question about the cisco WLC3500, if I perform a factory reset on the WLC3500 controller, will the permanent licenses that are in it be lost? Thanks in advance for the support.
Hi, I have a WLC 9800 and I want receive alerts of Rogue Malicious (Rogue APs and SSID) by email. Is it possible to configure this on WLC 9800? Another possibility would be to send this alerts from WLC 9800 to Solar Winds Monitoring (NMP). I don't fo...
Buenas,Necesito montar un sistema de autenticación wifi mediante certificado digital, sin sistema radius, solo con certificado digital.La ideas es que usuario tenga un certificado y en panel de cisco tengamos mismo certificado y que cuando haga conex...
Hi All,I would like some help on how to proceed in debugging the issue below for example, what type of logs etc. to collect and analyze. Issue: I have 2802i in mobility express mode with 8.10.185.0 version installed. Another 2702i connects to this ME...
Hey there,is it possible to use content filtering (Adult, Gaming etc.) via Group Policies just with MR Enterprise Licenses?There will be no MX in this installation, content filtering should all be done by MR.Do we need Advanced or Enterprise Licenses...
Hi, everybody. I need your help. I'm working at huge warehouse. I've lost one of the Cisco 1832 AP and i just have a serial number of that device. Is there a tool to find Cisco AP on local network by it's serial number?Thanks in advance.
I have sensors that claimed to DNAC and running while on wireless backhaul, but I am not able to ping them or SSH, even I have enabled the SSH. Also when I try to connect them through wired on a vlan has dhcp enabled option 43 still unreachable on dn...
